blob: 7953befe6e505f468fc311ba9f7fa1c55d49d713 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
|
<!-- retain these comments for translator revision tracking -->
<!-- original version: 24321 untranslated -->
<sect3 arch="ia64">
<title>Install the <command>ELILO</command> Boot Loader
on a Hard Disk</title>
<para>
The &architecture; boot loader is called <quote>elilo</quote>.
It is modeled on the <quote>lilo</quote> boot loader for the
x86 architecture and uses a similar configuration file.
However, instead of writing an MBR or partition boot record to
the disk, it copies the necessary files to a separate FAT formatted
disk partition and modifies the <guimenuitem>EFI Boot Manager</guimenuitem>
menu in the firmware to point to the files in the EFI partition.
The <command>elilo</command> boot loader is really in two parts.
The <filename>/usr/sbin/elilo</filename> command manages the partition and
copies file into it.
The <filename>elilo.efi</filename> program is copied into the EFI
partition and then run by the <quote>EFI Boot Manager</quote> to actually
do the work of loading and starting the Linux kernel.
</para><para>
The <quote>elilo</quote> configuration and installation is done as the
last step of installing the packages of the base installation.
&d-i; will present you with a list of potential disk partitions that it
has found suitable for an EFI partition.
Select the partition you set up earlier in the installation, typically
a partition on the same disk that contains your
<emphasis>root</emphasis> filesystem.
</para>
<warning><title>Choose the correct partition!</title>
<para>
The criteria for selecting a partition is that it is FAT format
filesystem with its <emphasis>boot</emphasis> flag set.
&d-i; may show multiple choices depending on what it finds from scanning
all of the disks of the system including EFI partitions of other system
disks and EFI diagnostic partitions.
Remember, the <command>elilo</command> may format the partition during
the installation, erasing any previous contents!
</para></warning>
</sect3>
<sect3 arch="ia64">
<title>EFI Partition Contents</title>
<para>
The EFI partition is a FAT filesystem format partition on one of the
hard disks of the system, usually the same disk that contains the
<emphasis>root</emphasis> filesystem.
It is normally not mounted on a running system as it is only needed
by the <quote>EFI Boot Manager</quote> to load the system and the
installer part of the <command>elilo</command> writes to the filesystem
directly.
The <command>/usr/sbin/elilo</command> utility writes the following files
into the <filename>efi/debian</filename> directory of the EFI
partition during the installation.
Note that the <quote>EFI Boot Manager</quote> would find these files
using the path <filename>fs<replaceable>n</replaceable>:\efi\debian</filename>.
There may be other files in this filesystem as well over time as
the system is updated or re-configured.
</para>
<variablelist>
<varlistentry>
<term><filename>elilo.conf</filename></term>
<listitem><para>
This is the configuration file read by the boot loader when it starts.
It is a copy of the <filename>/etc/elilo.conf</filename> with
the filenames re-written to refer to files in the EFI partition.
</para></listitem></varlistentry>
<varlistentry>
<term><filename>elilo.efi</filename></term>
<listitem><para>
This is the boot loader program that the <quote>EFI Boot Manager</quote>
runs to boot the system.
It is the program behind the <guimenuitem>Debian GNU/Linux</guimenuitem>
menu item of the <quote>EFI Boot Manager</quote> command menu.
</para></listitem></varlistentry>
<varlistentry>
<term><filename>initrd.img</filename></term>
<listitem><para>
This is the initial root filesystem used to boot the kernel.
It is a copy of the file referenced in the
<filename>/etc/elilo.conf</filename>.
In a standard Debian installation it would be the file in
<filename>/boot</filename> pointed to by the symbolic link
<filename>/initrd.img</filename>.
</para></listitem></varlistentry>
<varlistentry>
<term><filename>readme.txt</filename></term>
<listitem><para>
This is a small text file warning you that the contents of the
directory are managed by the <command>elilo</command> and that
any local changes would be lost at the next time
<filename>/usr/sbin/elilo</filename> is run.
</para></listitem></varlistentry>
<varlistentry>
<term><filename>vmlinuz</filename></term>
<listitem><para>
This is the compressed kernel itself.
It is a copy of the file referenced in the
<filename>/etc/elilo.conf</filename>.
In a standard Debian installation it would be the file in
<filename>/boot</filename> pointed to by the symbolic link
<filename>/vmlinuz</filename>.
</para></listitem></varlistentry>
</variablelist>
</sect3>
|
