blob: fadc600e37f234bcca13a923488b1bfc53c41e46 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
|
<!-- retain these comments for translator revision tracking -->
<!-- original version: 11648 untranslated -->
<sect2 arch="arm" id="boot-tftp"><title>Booting from TFTP</title>
&boot-installer-intro-net.xml;
<sect3 arch="arm"><title>Booting from TFTP on NetWinder</title>
<para>
NetWinders have two network interfaces: The 10Mbps NE2000-compatible
card is <filename>eth0</filename> and the 100Mbps Tulip card is
<filename>eth1</filename>.
</para><note><para>
You need NeTTrom 2.2.1 or later to boot the
installation system. NeTTrom 2.3.3 is recommended: get these files
from
<ulink url="ftp://ftp.netwinder.org/pub/netwinder/firmware/"></ulink>:
<itemizedlist>
<listitem><para>
<filename>nettrom-2.3-3.armv4l.rpm</filename>
</para></listitem>
<listitem><para>
<filename>nettrom-2.3.3.bin</filename>
</para></listitem>
<listitem><para>
<filename>nettrom-2.3.3.bin.md5sum</filename>
</para></listitem>
</itemizedlist>
</para></note><para>
After rebooting and interrupting the boot process during the countdown, you
must first configure the network either with a static address:
<informalexample><screen>
NeTTrom command-> setenv eth0_ip 192.168.0.10/24
</screen></informalexample>
where 24 is the number of set bits in the netmask, or a dynamic address:
<informalexample><screen>
NeTTrom command-> boot diskless
</screen></informalexample>
</para><para>
You may also need to configure the <userinput>route1</userinput>
settings if the TFTP
server is not on the local subnet. The rest of the config is pretty
standard (the save-all step is optional):
<informalexample><screen>
NeTTrom command-> setenv kerntftpserver 192.168.0.1
NeTTrom command-> setenv kerntftpfile tftpboot.img
NeTTrom command-> save-all
NeTTrom command-> setenv netconfig_eth0 flash
NeTTrom command-> setenv kernconfig tftp
</screen></informalexample>
</para><para>
Only the last two of these interfere with normal disk booting, so it is
safe to <command>save-all</command> right before it, which will
store the network settings in case you need to boot from the network
again. Use the <command>printenv</command> command to review your
environment settings. Finally, if your <envar>cmdappend</envar>
NeTTrom variable has the <option>noinitrd</option> option (which is
necessary to boot 2.4 kernels), you must remove it so the downloaded
kernel can boot with its attached ramdisk.
</para>
</sect3>
<sect3 arch="arm"><title>Booting from TFTP on CATS</title>
<para>
On CATS machines, use <command>boot de0:</command> or similar at the
Cyclone prompt.
</para>
</sect3>
</sect2>
<sect2 arch="arm"><title>Booting from CD-ROM</title>
&boot-installer-intro-cd.xml;
<para>
To boot a CD-ROM from the Cyclone console prompt, use the command
<command>boot cd0:cats.bin</command>
</para>
</sect2>
|
