Italian translation updated

1 files changed, 28 insertions, 23 deletions

diff --git a/it/install-methods/tftp/rarp.xml b/it/install-methods/tftp/rarp.xml
index 679186fb1..02c81b8b9 100644
--- a/it/install-methods/tftp/rarp.xml
+++ b/it/install-methods/tftp/rarp.xml
@@ -4,37 +4,34 @@
 
   <sect2 condition="supports-rarp" id="tftp-rarp">
   <!-- <title>Setting up RARP server</title> -->
-  <title>Attivare un server RARP</title>
-
+  <title>Attivazione di un server RARP</title>
 <para>
 
-<!-- To setup RARP, you need to know the Ethernet address (a.k.a. the MAC
+<!--
+To setup RARP, you need to know the Ethernet address (a.k.a. the MAC
 address) of the client computers to be installed.
-If you don't know this information, you can -->
+If you don't know this information, you can
+<phrase arch="sparc"> pick it off the initial OpenPROM boot messages,
+use the OpenBoot <userinput>.enet-addr</userinput> command, or </phrase>
+boot into <quote>Rescue</quote> mode (e.g., from the rescue floppy) and use the
+command <userinput>/sbin/ifconfig eth0</userinput>.
+-->
 
 Per impostare RARP è necessario conoscere l'indirizzo Ethernet (noto anche
 come indirizzo MAC) dei computer client da installare. Se non si conoscono
 queste informazioni è possibile
-
-<!-- <phrase arch="sparc"> pick it off the initial OpenPROM boot messages,
-use the OpenBoot <userinput>.enet-addr</userinput> command, or </phrase> -->
-
 <phrase arch="sparc">leggerlo nei primi messaggi durante l'avvio di OpenPROM,
 usare il comando <userinput>.enet-addr</userinput> di OpenBoot oppure</phrase>
-
-<!--
-boot into <quote>Rescue</quote> mode (e.g., from the rescue floppy) and use the
-command <userinput>/sbin/ifconfig eth0</userinput>.
--->
-
 avviare in modalità <quote>Ripristino</quote> (p.e. da un dischetto di
 ripristino) e usare il comando <userinput>/sbin/ifconfig eth0</userinput>.
 
 </para><para>
 
-<!-- On a RARP server system using a Linux 2.2.x kernel,
+<!--
+On a RARP server system using a Linux 2.2.x kernel,
 you need to populate the kernel's RARP table.
-To do this, run the following commands: -->
+To do this, run the following commands:
+-->
 
 Su un sistema con Linux 2.2.x e un server RARP è necessario popolare la
 tabella RARP del kernel. Per farlo usare i seguenti comandi:
@@ -49,7 +46,9 @@ tabella RARP del kernel. Per farlo usare i seguenti comandi:
 <replaceable>client-enet-addr</replaceable></userinput>
 </screen></informalexample>
 
-<!-- If you get -->
+<!--
+If you get
+-->
 
 Se si ottiene
 
@@ -57,9 +56,11 @@ Se si ottiene
 SIOCSRARP: Invalid argument
 </screen></informalexample>
 
-<!-- you probably need to load the RARP kernel module or else recompile the
+<!--
+you probably need to load the RARP kernel module or else recompile the
 kernel to support RARP.  Try <userinput>modprobe rarp</userinput> and
-then try the <command>rarp</command> command again. -->
+then try the <command>rarp</command> command again.
+-->
 
 probabilmente si deve caricare il modulo del kernel RARP oppure
 ricompilare il kernel inserendo il supporto RARP. Eseguire
@@ -68,11 +69,13 @@ comando <command>rarp</command>.
 
 </para><para>
 
-<!-- On a RARP server system using a Linux 2.4.x kernel,
+<!--
+On a RARP server system using a Linux 2.4.x kernel,
 there is no RARP module, and
 you should instead use the <command>rarpd</command> program.  The
 procedure is similar to that used under SunOS in the following
-paragraph. -->
+paragraph.
+-->
 
 Su un sistema con Linux 2.4.x e un server RARP non esiste il modulo RARP e
 al suo posto si deve usare il programma <command>rarpd</command>. La
@@ -81,13 +84,15 @@ paragrafo.
 
 </para><para>
 
-<!-- Under SunOS, you need to ensure that the Ethernet hardware address for
+<!--
+Under SunOS, you need to ensure that the Ethernet hardware address for
 the client is listed in the <quote>ethers</quote> database (either in the
 <filename>/etc/ethers</filename> file, or via NIS/NIS+) and in the
 <quote>hosts</quote> database. Then you need to start the RARP daemon.  In SunOS
 4, issue the command (as root):
 <userinput>/usr/etc/rarpd -a</userinput>; in SunOS 5, use
-<userinput>/usr/sbin/rarpd -a</userinput>. -->
+<userinput>/usr/sbin/rarpd -a</userinput>.
+-->
 
 Sotto SunOS ci si deve assicurare che l'indirizzo Ethernet del
 client sia elencato nel database <quote>ethers</quote> (nel file