- Switch Finnish from XML-based to PO-based translation

- Correct placement of changelog entries from Joey

1 files changed, 0 insertions, 100 deletions

diff --git a/fi/boot-installer/mips.xml b/fi/boot-installer/mips.xml
deleted file mode 100644
index f628be2c9..000000000
--- a/fi/boot-installer/mips.xml
+++ /dev/null
@@ -1,100 +0,0 @@
-<!-- retain these comments for translator revision tracking -->
-<!-- original version: 35613 untranslated -->
-
-
-  <sect2 arch="mips" id="boot-tftp"><title>Booting with TFTP</title>
-
-   <sect3>
-   <title>SGI TFTP Booting</title>
-<para>
-
-After entering the command monitor use
-
-<informalexample><screen>
-bootp():
-</screen></informalexample>
-
-on SGI machines to boot linux and to begin installation of the Debian
-Software.  In order to make this
-work you may have to unset the <envar>netaddr</envar> environment
-variable. Type
-
-<informalexample><screen>
-unsetenv netaddr
-</screen></informalexample>
-
-in the command monitor to do this.
-
-</para>
-  </sect3>
-
-   <sect3>
-   <title>Broadcom BCM91250A and BCM91480B TFTP Booting</title>
-<para>
-
-On the Broadcom BCM91250A and BCM91480B evaluation boards, you have to load the SiByl boot
-loader via TFTP which will then load and start the Debian installer.  In
-most cases, you will first obtain an IP address via DHCP but it is also
-possible to configure a static address.  In order to use DHCP, you can
-enter the following command on the CFE prompt:
-
-<informalexample><screen>
-ifconfig eth0 -auto
-</screen></informalexample>
-
-Once you have obtained an IP address, you can load SiByl with the following
-command:
-
-<informalexample><screen>
-boot 192.168.1.1:/boot/sibyl
-</screen></informalexample>
-
-You need to substitute the IP address listed in this example with either
-the name or the IP address of your TFTP server.  Once you issue this
-command, the installer will be loaded automatically.
-
-</para>
-</sect3>
-  </sect2>
-
-  <sect2 arch="mips"><title>Boot Parameters</title>
-
-   <sect3>
-   <title>SGI TFTP Booting</title>
-<para>
-
-On SGI machines you can append boot parameters to the
-<command>bootp():</command> command in the command monitor.
-
-</para><para>
-
-Following the <command>bootp():</command> command you can give the
-path and name of the file to boot if you did not give an explicit name
-via your bootp/dhcp server. Example:
-
-<informalexample><screen>
-bootp():/boot/tftpboot.img
-</screen></informalexample>
-
-Further kernel parameters can be passed via <command>append</command>:
-
-<informalexample><screen>
-bootp(): append="root=/dev/sda1"
-</screen></informalexample>
-
-</para>
-  </sect3>
-
-   <sect3>
-   <title>Broadcom BCM91250A and BCM91480B TFTP Booting</title>
-<para>
-
-You cannot pass any boot parameters directly from the CFE prompt.  Instead,
-you have to edit the <filename>/boot/sibyl.conf</filename> file on the TFTP
-server and add your parameters to the <replaceable>extra_args</replaceable>
-variable.
-
-</para>
-  </sect3>
-
-  </sect2>