- Switch Finnish from XML-based to PO-based translation

- Correct placement of changelog entries from Joey

1 files changed, 0 insertions, 219 deletions

diff --git a/fi/boot-installer/arm.xml b/fi/boot-installer/arm.xml
deleted file mode 100644
index 5e17ac9ac..000000000
--- a/fi/boot-installer/arm.xml
+++ /dev/null
@@ -1,219 +0,0 @@
-<!-- retain these comments for translator revision tracking -->
-<!-- original version: 36639 untranslated -->
-
-  <sect2 arch="arm" id="boot-tftp"><title>Booting from TFTP</title>
-
-&boot-installer-intro-net.xml;
-
-   <sect3 arch="arm"><title>Booting from TFTP on Netwinder</title>
-<para>
-
-Netwinders have two network interfaces: A 10Mbps NE2000-compatible
-card (which is generally referred to as <literal>eth0</literal>) and
-a 100Mbps Tulip card.  There may be problems loading the image via TFTP
-using the 100Mbps card so it is recommended that you use the 10Mbps
-interface (the one labeled with <literal>10 Base-T</literal>).
-
-</para>
-<note><para>
-
-You need NeTTrom 2.2.1 or later to boot the installation system, and
-version 2.3.3 is recommended.  Unfortunately, firmware files are currently
-not available for download because of license issues.  If this situation
-changes, you may find new images at <ulink url="http//www.netwinder.org/"></ulink>.
-
-</para></note>
-<para>
-
-When you boot your Netwinder you have to interrupt the boot process during the
-countdown.  This allows you to set a number of firmware settings needed in
-order to boot the installer.  First of all, start by loading the default
-settings:
-
-<informalexample><screen>
-    NeTTrom command-&gt; load-defaults
-</screen></informalexample>
-
-Furthermore, you must configure the network, either with a static address:
-
-<informalexample><screen>
-    NeTTrom command-&gt; setenv netconfig_eth0 flash
-    NeTTrom command-&gt; setenv eth0_ip 192.168.0.10/24
-</screen></informalexample>
-
-where 24 is the number of set bits in the netmask, or a dynamic address:
-
-<informalexample><screen>
-    NeTTrom command-&gt; setenv netconfig_eth0 dhcp
-</screen></informalexample>
-
-You may also need to configure the <userinput>route1</userinput>
-settings if the TFTP server is not on the local subnet.
-
-Following these settings, you have to specify the TFTP server and the
-location of the image.  You can then store your settings to flash.
-
-<informalexample><screen>
-    NeTTrom command-&gt; setenv kerntftpserver 192.168.0.1
-    NeTTrom command-&gt; setenv kerntftpfile boot.img
-    NeTTrom command-&gt; save-all
-</screen></informalexample>
-
-Now you have to tell the firmware that the TFTP image should be booted:
-
-<informalexample><screen>
-    NeTTrom command-&gt; setenv kernconfig tftp
-    NeTTrom command-&gt; setenv rootdev /dev/ram
-</screen></informalexample>
-
-If you use a serial console to install your Netwinder, you need to add the
-following setting:
-
-<informalexample><screen>
-    NeTTrom command-&gt; setenv cmdappend root=/dev/ram console=ttyS0,115200
-</screen></informalexample>
-
-Alternatively, for installations using a keyboard and monitor you have to
-set:
-
-<informalexample><screen>
-    NeTTrom command-&gt; setenv cmdappend root=/dev/ram
-</screen></informalexample>
-
-You can use the <command>printenv</command> command to review your
-environment settings.  After you have verified that the settings are
-correct, you can load the image:
-
-<informalexample><screen>
-    NeTTrom command-&gt; boot
-</screen></informalexample>
-
-In case you run into any problems, a <ulink
-url="http://www.netwinder.org/howto/Firmware-HOWTO.html">detailed
-HOWTO</ulink> is available.
-
-</para>
-   </sect3>
-
-   <sect3 arch="arm"><title>Booting from TFTP on CATS</title>
-<para>
-
-On CATS machines, use <command>boot de0:</command> or similar at the
-Cyclone prompt.
-
-</para>
-   </sect3>
-  </sect2>
-
-
-  <sect2 arch="arm"><title>Booting from CD-ROM</title>
-
-&boot-installer-intro-cd.xml;
-
-<para>
-
-To boot a CD-ROM from the Cyclone console prompt, use the command
-<command>boot cd0:cats.bin</command>
-
-</para>
-  </sect2>
-
-
-  <sect2 arch="arm" id="boot-firmware"><title>Booting from Firmware</title>
-
-&boot-installer-intro-firmware.xml;
-
-   <sect3 arch="arm" id="boot-firmware-nslu2"><title>Booting the NSLU2</title>
-<para>
-
-There are three ways how to put the installer firmware into flash:
-
-</para>
-
-    <sect4 arch="arm"><title>Using the NSLU2 web interface</title>
-<para>
-
-Go to the administration section and choose the menu item
-<literal>Upgrade</literal>.  You can then browse your disk for the
-installer image you have previously downloaded.  Then press the
-<literal>Start Upgrade</literal> button, confirm, wait for a few minutes
-and confirm again.  The system will then boot straight into the installer.
-
-</para>
-    </sect4>
-
-    <sect4 arch="arm"><title>Via the network using Linux/Unix</title>
-<para>
-
-You can use <command>upslug2</command> from any Linux or Unix machine to
-upgrade the machine via the network.  This software is packaged for
-Debian.
-
-First, you have to put your NSLU2 in upgrade mode:
-
-<orderedlist>
-<listitem><para>
-
-Disconnect any disks and/or devices from the USB ports.
-
-</para></listitem>
-<listitem><para>
-
-Power off the NSLU2
-
-</para></listitem>
-<listitem><para>
-
-Press and hold the reset button (accessible through the small hole on the
-back just above the power input).
-
-</para></listitem>
-<listitem><para>
-
-Press and release the power button to power on the NSLU2.
-
-</para></listitem>
-<listitem><para>
-
-Wait for 10 seconds watching the ready/status LED. After 10 seconds it
-will change from amber to red. Immediately release the reset button.
-
-</para></listitem>
-<listitem><para>
-
-The NSLU2 ready/status LED will flash alternately red/green (there is a 1
-second delay before the first green). The NSLU2 is now in upgrade mode.
-
-</para></listitem>
-</orderedlist>
-
-See the <ulink
-url="http://www.nslu2-linux.org/wiki/OpenSlug/UsingTheBinary">NSLU2-Linux
-pages</ulink> if you have problems with this.
-
-Once your NSLU2 is in upgrade mode, you can flash the new image:
-
-<informalexample><screen>
-sudo upslug2 -i di-nslu2.bin
-</screen></informalexample>
-
-Note that the tool also shows the MAC address of your NSLU2, which may come
-in handy to configure your DHCP server.  After the whole image has been
-written and verified, the system will automatically reboot.  Make sure you
-connect your USB disk again now, otherwise the installer won't be able to
-find it.
-
-</para>
-    </sect4>
-
-    <sect4 arch="arm"><title>Via the network using Windows</title>
-<para>
-
-There is <ulink
-url="http://www.everbesthk.com/8-download/sercomm/firmware/all_router_utility.zip">a
-tool</ulink> for Windows to upgrade the firmware via the network.
-
-</para>
-    </sect4>
-   </sect3>
-  </sect2>