| Age | Commit message (Collapse) | Author |
|---|
|
The shpc component is optional while ACPI hotplug is used
for hot-plugging PCI devices into a PCI-PCI bridge.
Disabling the shpc by default will make slot 0 usable at boot time
and not only for hot-plug, without loosing any functionality.
Older machines will have shpc enabled for compatibility reasons.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
For configurations of the pflash_cfi01 device which set it up with a
device-width not equal to the width (ie where we are emulating
multiple narrow flash devices wired up in parallel), we were giving
incorrect values in the CFI data table:
(1) the sector length entry should specify the sector length for a
single device, not the length for the overall collection of
devices
(2) the number of blocks per device must not be divided by the
number of devices because the resulting device size would not
match the overall size
(3) this then means that the overall write block size must be
modified depending on the number of devices because the entry is
per device and when the guest writes into the flash it
calculates the write size by using the CFI entry (write size
per device) multiplied by the number of chips.
(It would alternatively be possible to modify the write
block size in the CFI table (currently hardcoded at 2048) and
leave the overall write block size alone.)
This commit corrects these bugs, and adds a hw-compat property
to retain the old behaviour on 2.8 and earlier versions. (The
only board we have which uses this sort of flash config and
has machine versioning is the "virt" board -- the PC uses a
single flash device and so behaviour is unaffected whether
using old-multiple-chip-handling or not.)
Here is a configuration example from the vexpress board:
VEXPRESS_FLASH_SIZE = 64M
VEXPRESS_FLASH_SECT_SIZE 256K
num-blocks = VEXPRESS_FLASH_SIZE / VEXPRESS_FLASH_SECT_SIZE = 256
sector-length = 256K
width = 4
device-width = 2
The code will fill the CFI entry with the following entries:
num-blocks = 256
sector-length = 128K
writeblock_size = 2048
This results in two chips, each with 256 * 128K = 32M device size and
a write block size of 2048.
A sector erase will be sent to both chips, thus 256K must be erased.
When the guest sends a block write command, it will write 4096 bytes
data at once (2048 per device).
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: cleaned up and expanded commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
More precisely, the "x-file-slots" count is bumped for all machine types
that:
(a) use fw_cfg, and
(b) are not versioned (hence migration is not expected to work for them
across QEMU releases anyway), or have version 2.9.
This affects machine types implemented in the following source files:
- "hw/arm/virt.c". The "virt-*" machine type is versioned, and the <= 2.8
versions already depend on HW_COMPAT_2_8 (see commit e353aac51b944).
Therefore adding the "x-file-slots" compat values to HW_COMPAT_2_8
suffices.
- "hw/i386/pc.c". The "pc-i440fx-*" (including "pc-*") and "pc-q35-*"
machine types are versioned. Modifying HW_COMPAT_2_8 is sufficient here
too (see commit "pc: Add 2.9 machine-types"). The "isapc" machtype is
not versioned. The "xenfv" machine type, which uses fw_cfg for direct
kernel booting, is also not versioned.
- "hw/ppc/mac_newworld.c". The "mac99" machine type is not versioned.
- "hw/ppc/mac_oldworld.c". The "g3beige" machine type is not versioned.
- "hw/sparc/sun4m.c". None of the 9 machine types defined in this file
appear versioned.
- "hw/sparc64/sun4u.c". None of the 3 machine types defined in this file
appear versioned.
Cc: "Gabriel L. Somlo" <somlo@cmu.edu>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Artyom Tarasenko <atar4qemu@gmail.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Gabriel Somlo <somlo@cmu.edu>
Tested-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
|
|
This patch fixes a cross-version migration regression introduced
by commit d1b4259f ("virtio-bus: Plug devices after features are
negotiated").
The problem is encountered when host's vhost backend does not support
VIRTIO_F_VERSION_1, and migration is initiated from a v2.7 or prior
machine with virtio-pci modern capabilities enabled to a v2.8 machine.
In this case, modern capabilities get exposed to the guest by the source,
whereas the target will detect version 1 is not supported so will only
expose legacy capabilities.
The problem is fixed by introducing a new "x-ignore-backend-features"
property, which is set in v2.7 and prior compatibility modes. Doing this,
v2.7 machine keeps its broken behaviour (enabling modern while version
is not supported), and newer machines will behave correctly.
Reported-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Message-id: 20161214163035.3297-1-maxime.coquelin@redhat.com
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Cluster x2APIC cannot work without KVM's x2apic API when the maximal
APIC ID is greater than 8 and only KVM's LAPIC can support x2APIC, so we
forbid other APICs and also the old KVM case with less than 9, to
simplify the code.
There is no point in enabling EIM in forbidden APICs, so we keep it
enabled only for the KVM APIC; unconditionally, because making the
option depend on KVM version would be a maintanance burden.
Old QEMUs would enable eim whenever intremap was on, which would trick
guests into thinking that they can enable cluster x2APIC even if any
interrupt destination would get clamped to 8 bits.
Depending on your configuration, QEMU could notice that the destination
LAPIC is not present and report it with a very non-obvious:
KVM: injection failed, MSI lost (Operation not permitted)
Or the guest could say something about unexpected interrupts, because
clamping leads to aliasing so interrupts were being delivered to
incorrect VCPUs.
KVM_X2APIC_API is the feature that allows us to enable EIM for KVM.
QEMU 2.7 allowed EIM whenever interrupt remapping was enabled. In order
to keep backward compatibility, we again allow guests to misbehave in
non-obvious ways, and make it the default for old machine types.
A user can enable the buggy mode it with "x-buggy-eim=on".
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Add support for enabling the virtio 1.0 "emergency write"
(VIRTIO_CONSOLE_F_EMERG_WRITE) feature. The previous patch introduced
the plumbing required for this; now we expose the virtio feature to
the guest. The feature is disabled for compatibility machines to avoid
exposing a new feature to existing guests.
As required by the virtio 1.0 spec, the emergency write functionality
is available to the guest even if the guest doesn't negotatiate the
feature, as well as before feature negotation.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
It's 2.8 now, and maybe it's time to switch IOAPIC default version to
0x20.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1474608795-23058-1-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Currently each VQ Notification Virtio Capability is allocated
on a different page. The idea is to enable split drivers within
guests, however there are no known plans to do that.
The allocation will result in a 8MB BAR, more than various
guest firmwares pre-allocates for PCI Bridges hotplug process.
Reserve 4 bytes per VQ by default and add a new parameter
"page-per-vq" to be used with split drivers.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Enable transitional virtio devices by default.
Enable virtio-1.0 for devices plugged into
PCIe ports (Root ports or Downstream ports).
Using the virtio-1 mode will remove the limitation
of the number of devices that can be attached to a machine
by removing the need for the IO BAR.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
We changed link status register in pci express endpoint capability
over time. Specifically,
commit b2101eae63ea57b571cee4a9075a4287d24ba4a4 ("pcie: Set the "link
active" in the link status register") set data link layer link active
bit in this register without adding compatibility to old machine types.
When migrating from qemu 2.3 and older this affects xhci devices which
under machine type 2.0 and older have a pci express endpoint capability
even if they are on a pci bus.
Add compatibility flags to make this bit value match what it was under
2.3.
Additionally, to avoid breaking migration from qemu 2.3 and up,
suppress checking link status during migration: this seems sane
since hardware can change link status at any time.
https://bugzilla.redhat.com/show_bug.cgi?id=1352860
Reported-by: Gerd Hoffmann <kraxel@redhat.com>
Fixes: b2101eae63ea57b571cee4a9075a4287d24ba4a4
("pcie: Set the "link active" in the link status register")
Cc: qemu-stable@nongnu.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
At the moment the following QEMU command line triggers an assertion
failure (minimal reproducer by Cole):
qemu-system-aarch64 \
-machine virt-2.6,accel=tcg \
-nodefaults \
-no-user-config \
-nographic -monitor stdio \
-device virtio-scsi-device,id=scsi0 \
-device virtio-scsi-device,id=scsi1 \
-drive file=foo.img,format=raw,if=none,id=d0 \
-device scsi-hd,bus=scsi0.0,drive=d0 \
-drive file=foo.img,format=raw,if=none,id=d1 \
-device scsi-hd,bus=scsi1.0,drive=d1
qemu-system-aarch64: migration/savevm.c:615:
vmstate_register_with_alias_id:
Assertion `!se->compat || se->instance_id == 0' failed.
The reason is that the vmstate sections for the two scsi-hd devices are
not uniquely identifiable by name.
The direct parent buses of the scsi-hd devices -- scsi0.0 and scsi1.0 --
support the BusClass.get_dev_path member function. scsibus_get_dev_path()
formats a device path prefix with the help of its topologically parent
bus, and then appends the chan:id:lun triplet to it. For both scsi-hd
devices, this triplet is 0:0:0.
(Here we use "device path" in the QEMU migration sense, for vmstate
section identification, not in the OFW or UEFI device path senses.)
The virtio-scsi HBA is plugged into the virtio-mmio bus (implemented by
the internal VirtIOMMIOProxy device). This bus class
(TYPE_VIRTIO_MMIO_BUS) inherits, as its get_dev_path() member function,
the virtio_bus_get_dev_path() method from its parent class
(TYPE_VIRTIO_BUS).
virtio_bus_get_dev_path() does not format any kind of device address on
its own; "virtio addresses" are transport-specific. Therefore
virtio_bus_get_dev_path() asks the topologically parent bus of the proxy
object (implementing the specific virtio transport) to format the address
of the proxy object.
(For virtio-pci devices (where the proxy is an instance of VirtIOPCIProxy,
plugged into a PCI bus), this ends up in pcibus_get_dev_path().)
However, VirtIOMMIOProxy is usually (in practice: always) plugged into
"main-system-bus", the singleton TYPE_SYSTEM_BUS object. This BusClass
does not support formatting QEMU vmstate device paths at all (as
SysBusDevice objects can have zero or more IO ports and zero or more MMIO
regions). Hence the formatting request delegated from
virtio_bus_get_dev_path() gets answered with NULL.
The end result is that the two scsi-hd devices end up with the same device
path "0:0:0", which triggers the assert.
We can solve this by recognizing that virtio-mmio transports are
distinguished from each other by their base addresses in MMIO address
space. Implement virtio_mmio_bus_get_dev_path() as follows:
(1) The virtio device whose devpath is to be formatted resides on a
virtio-mmio bus that is implemented by a VirtIOMMIOProxy object. Ask
the parent bus of VirtIOMMIOProxy to format the device path of
VirtIOMMIOProxy, as a path prefix. (This is identical to what
virtio_bus_get_dev_path() does.)
(2) Append the base address of VirtIOMMIOProxy to the device path, such
as:
- virtio-mmio@000000000a003e00,
- virtio-mmio@000000000a003c00.
Given that these device paths are placed in the migration stream, step (2)
above, if done unconditionally, would break migration. So make that step
conditional on a new VirtIOMMIOProxy property, which is enabled for 2.7
machine types and later.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Cole Robinson <crobinso@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Kevin Zhao <kevin.zhao@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Tom Hanson <thomas.hanson@linaro.org>
Reported-by: Kevin Zhao <kevin.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 1467739394-28357-1-git-send-email-lersek@redhat.com
Fixes: https://bugs.launchpad.net/qemu/+bug/1594239
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Also add some of the option cascading we were missing.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
When I reviewed Marc's fw_cfg DMA patches, I completely missed that the
way we set dma_enabled would break migration.
Gerd explained the right way (see reference below): dma_enabled should be
set to true by default, and only true->false transitions should be
possible:
- when the user requests that with
-global fw_cfg_mem.dma_enabled=off
or
-global fw_cfg_io.dma_enabled=off
as appropriate for the platform,
- when HW_COMPAT_2_4 dictates it,
- when board code initializes fw_cfg without requesting DMA support.
Cc: Marc Marí <markmb@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Alexandre DERUMIER <aderumier@odiso.com>
Cc: qemu-stable@nongnu.org
Ref: http://thread.gmane.org/gmane.comp.emulators.qemu/390272/focus=391042
Ref: https://bugs.launchpad.net/qemu/+bug/1536487
Suggested-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 1455823860-22268-1-git-send-email-lersek@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
The 2.88 drive is more suitable as a default because
it can still read 1.44 images correctly, but the reverse
is not true.
Since there exist virtio-win drivers that are shipped on
2.88 floppy images, this patch will allow VMs booted without
a floppy disk inserted to later insert a 2.88MB floppy and
have that work.
This patch has been tested with msdos, freedos, fedora,
windows 8 and windows 10 without issue: if problems do
arise for certain guests being unable to cope with 2.88MB
drives as the default, they are in the minority and can use
type=144 as needed (or insert a proper boot medium and omit
type=144/288 or use type=auto) to obtain different drive types.
As icing, the default will remain auto/144 for any pre-2.6
machine types, hopefully minimizing the impact of this change
in legacy hw to basically zero.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1453495865-9649-13-git-send-email-jsnow@redhat.com
|
|
2.5 specific
pvscsi's x-disable-pcie and x-old-pci-configuration backward compat
properties were introduced in 952970b and d5da3ef:
vmw_pvscsi: Introduce 'x-old-pci-configuration' backword compatability property
vmw_pvscsi: Introduce 'x-disable-pcie' backword compatability property
and were placed into HW_COMPAT_2_4.
However since these commits were pulled post v2.5, move them to
HW_COMPAT_2_5.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Message-Id: <1450900558-20113-1-git-send-email-shmulik.ladkani@ravellosystems.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Following the previous patch which changed vmxnet3 to be a pci express
device, this patch introduces a boolean property 'x-disable-pcie' whose
default is false.
Setting 'x-disable-pcie' to 'on' preserves the old 'pci device' (non
express) behavior. This allows migration to older versions.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Following the previous patches, where vmxnet3's pci's msi/msix
capability offsets and msix's PBA table offsets have been changed, this
patch introduces a boolean property 'x-old-msi-offsets' to vmxnet3,
whose default is false.
Setting 'x-old-msi-offsets' to 'on' preserves the old offsets behavior,
which allows migration to older versions.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Cosmetic change only.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
|
|
Add pc-i440fx-2.6 and pc-q35-2.6 machine classes.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
|
|
Following the previous patch which changed pvscsi to be a pci express
device, this patch introduces a boolean property 'x-disable-pcie'.
Its default value is false, exposing pvscsi as a pcie device.
Setting 'x-disable-pcie' to 'on' preserves the old 'pci device' (non
express) behavior. This allows migration to older versions.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Message-Id: <1449994112-7054-7-git-send-email-shmulik.ladkani@ravellosystems.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Following the previous patches, which introduced various changes in
pvscsi's pci configuration space (device subsystem id and revision, msi
offset), this patch introduces a boolean property
'x-old-pci-configuration' to pvscsi.
Its default value is false, exposing the above changes in the pci config
space.
Setting 'x-old-pci-configuration' to 'on' preserves the old behavior,
which allows migration to older versions.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Message-Id: <1449994112-7054-4-git-send-email-shmulik.ladkani@ravellosystems.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
virtio, vhost: fixes for 2.5
This fixes a performance regression with virtio 1,
and makes device stop/start more robust for vhost-user.
virtio devices on pcie bus now have pcie and pm
capability, as required by the PCI Express spec.
migration now works better with virtio 9p.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 12 Nov 2015 14:40:42 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
virtio-9p: add savem handlers
hw/virtio: Add PCIe capability to virtio devices
vhost: send SET_VRING_ENABLE at start/stop
vhost: rename RESET_DEVICE backto RESET_OWNER
vhost-user: modify SET_LOG_BASE to pass mmap size and offset
virtio-pci: unbreak queue_enable read
virtio-pci: introduce pio notification capability for modern device
virtio-pci: use zero length mmio eventfd for 1.0 notification cap when possible
KVM: add support for any length io eventfd
memory: don't try to adjust endianness for zero length eventfd
virtio-pci: fix 1.0 virtqueue migration
Conflicts:
include/hw/compat.h
[Fixed a trivial merge conflict in compat.h]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The virtio devices are converted to PCI-Express
if they are plugged into a PCI-Express bus and
the 'modern' protocol is enabled.
Devices plugged directly into the Root Complex as
Integrated Endpoints remain PCI.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
We don't migrate the followings fields for virtio-pci:
uint32_t dfselect;
uint32_t gfselect;
uint32_t guest_features[2];
struct {
uint16_t num;
bool enabled;
uint32_t desc[2];
uint32_t avail[2];
uint32_t used[2];
} vqs[VIRTIO_QUEUE_MAX];
This will confuse driver if migrating during initialization. Solves
this issue by:
- introduce transport specific callbacks to load and store extra
virtqueue states.
- add a new subsection for virtio to migrate transport specific modern
device state.
- implement pci specific callbacks.
- add a new property for virtio-pci for whether or not to migrate
extra state.
- compat the migration for 2.4 and elder machine types
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
This follows the previous patches, where support for migrating the
entire MAC registers' array, and some new MAC registers were introduced.
This patch introduces the e1000-specific boolean parameter
"extra_mac_registers", which is on by default. Setting it to off will
enable migration to older versions of QEMU, but will disable the read
and write access to the new registers, that were introduced since adding
the ability to migrate the entire MAC array.
Example for usage to enable backward compatibility and to disable the
new MAC registers:
qemu-system-x86_64 -device e1000,extra_mac_registers=off,... ...
As mentioned above, the default value is "on".
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Devices that are compliant with virtio-1 do not support scsi
passthrough any more (and it has not been a recommended setup
anyway for quite some time). To avoid having to switch it off
explicitly in newer qemus that turn on virtio-1 by default, let's
switch the default to scsi=false for 2.5.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-id: 1444991154-79217-4-git-send-email-cornelia.huck@de.ibm.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Exceptions:
- virtio-blk
- compat machine types
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Now we can make everything consistent and define the macros even if they
are still empty.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Changing the convention to include commas inside the macros will allow
macros containing empty lists to be defined and used without compilation
errors.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Current support for bus master (clearing OK bit) together with the need to
support guests which do not enable PCI bus mastering, leads to extra state in
VIRTIO_PCI_FLAG_BUS_MASTER_BUG bit, which isn't robust in case of cross-version
migration for the case when guests use the device before setting DRIVER_OK.
Rip out this code, and replace it:
- Modern QEMU doesn't need VIRTIO_PCI_FLAG_BUS_MASTER_BUG
so just drop it for latest machine type.
- For compat machine types, set PCI_COMMAND if DRIVER_OK
is set.
As this is needed for 2.1 for both pc and ppc, move PC_COMPAT macros from pc.h
to a new common header.
Cc: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
|
