# SOME DESCRIPTIVE TITLE.
# Copyright (C) YEAR Free Software Foundation, Inc.
# FIRST AUTHOR <EMAIL@ADDRESS>, YEAR.
#
#, fuzzy
msgid ""
msgstr ""
"Project-Id-Version: PACKAGE VERSION\n"
"POT-Creation-Date: 2006-04-28 19:33+0000\n"
"PO-Revision-Date: YEAR-MO-DA HO:MI+ZONE\n"
"Last-Translator: FULL NAME <EMAIL@ADDRESS>\n"
"Language-Team: LANGUAGE <LL@li.org>\n"
"MIME-Version: 1.0\n"
"Content-Type: application/x-xml2pot; charset=UTF-8\n"
"Content-Transfer-Encoding: ENCODING\n"

#: boot-installer.xml:4
#, no-c-format
#. Tag: title
msgid "Booting the Installation System"
msgstr ""

#: boot-installer.xml:9
#, no-c-format
#. Tag: title
msgid "Booting the Installer on &arch-title;"
msgstr ""

#: boot-installer.xml:20
#, no-c-format
#. Tag: title
msgid "Alpha Console Firmware"
msgstr ""

#: boot-installer.xml:21
#, no-c-format
#. Tag: para
msgid "Console firmware is stored in a flash ROM and started when an Alpha system is powered up or reset. There are two different console specifications used on Alpha systems, and hence two classes of console firmware available:"
msgstr ""

#: boot-installer.xml:31
#, no-c-format
#. Tag: para
msgid "<emphasis>SRM console</emphasis>, based on the Alpha Console Subsystem specification, which provides an operating environment for OpenVMS, Tru64 UNIX, and Linux operating systems."
msgstr ""

#: boot-installer.xml:38
#, no-c-format
#. Tag: para
msgid "<emphasis>ARC, AlphaBIOS, or ARCSBIOS console</emphasis>, based on the Advanced RISC Computing (ARC) specification, which provides an operating environment for Windows NT."
msgstr ""

#: boot-installer.xml:47
#, no-c-format
#. Tag: para
msgid "From the user's perspective, the most important difference between SRM and ARC is that the choice of console constrains the possible disk-partitioning scheme for the hard disk which you wish to boot off of."
msgstr ""

#: boot-installer.xml:54
#, no-c-format
#. Tag: para
msgid "ARC requires that you use an MS-DOS partition table (as created by <command>cfdisk</command>) for the boot disk. Therefore MS-DOS partition tables are the <quote>native</quote> partition format when booting from ARC. In fact, since AlphaBIOS contains a disk partitioning utility, you may prefer to partition your disks from the firmware menus before installing Linux."
msgstr ""

#: boot-installer.xml:63
#, no-c-format
#. Tag: para
msgid "Conversely, SRM is <emphasis>incompatible</emphasis><footnote> <para> Specifically, the bootsector format required by the Console Subsystem Specification conflicts with the placement of the DOS partition table. </para> </footnote> with MS-DOS partition tables. Since Tru64 Unix uses the BSD disklabel format, this is the <quote>native</quote> partition format for SRM installations."
msgstr ""

#: boot-installer.xml:76
#, no-c-format
#. Tag: para
msgid "GNU/Linux is the only operating system on Alpha that can be booted from both console types, but &debian; &release; only supports booting on SRM-based systems. If you have an Alpha for which no version of SRM is available, if you will be dual-booting the system with Windows NT, or if your boot device requires ARC console support for BIOS initialization, you will not be able to use the &debian; &release; installer. You can still run &debian; &release; on such systems by using other install media; for instance, you can install Debian woody with MILO and upgrade."
msgstr ""

#: boot-installer.xml:87
#, no-c-format
#. Tag: para
msgid "Because <command>MILO</command> is not available for any of the Alpha systems currently in production (as of February 2000), and because it is no longer necessary to buy an OpenVMS or Tru64 Unix license to have SRM firmware on your older Alpha, it is recommended that you use SRM when possible."
msgstr ""

#: boot-installer.xml:95
#, no-c-format
#. Tag: para
msgid "The following table summarizes available and supported system type/console combinations (see <xref linkend=\"alpha-cpus\"/> for the system type names). The word <quote>ARC</quote> below denotes any of the ARC-compliant consoles."
msgstr ""

#: boot-installer.xml:107
#, no-c-format
#. Tag: entry
msgid "System Type"
msgstr ""

#: boot-installer.xml:108
#, no-c-format
#. Tag: entry
msgid "Console Type Supported"
msgstr ""

#: boot-installer.xml:114
#, no-c-format
#. Tag: entry
msgid "alcor"
msgstr ""

#: boot-installer.xml:115 boot-installer.xml:118 boot-installer.xml:124 boot-installer.xml:130 boot-installer.xml:133 boot-installer.xml:136 boot-installer.xml:139 boot-installer.xml:145 boot-installer.xml:148 boot-installer.xml:151 boot-installer.xml:160 boot-installer.xml:169 boot-installer.xml:184 boot-installer.xml:187
#, no-c-format
#. Tag: entry
msgid "ARC or SRM"
msgstr ""

#: boot-installer.xml:117
#, no-c-format
#. Tag: entry
msgid "avanti"
msgstr ""

#: boot-installer.xml:120
#, no-c-format
#. Tag: entry
msgid "book1"
msgstr ""

#: boot-installer.xml:121 boot-installer.xml:127 boot-installer.xml:142 boot-installer.xml:154 boot-installer.xml:163 boot-installer.xml:166 boot-installer.xml:172 boot-installer.xml:178 boot-installer.xml:181
#, no-c-format
#. Tag: entry
msgid "SRM only"
msgstr ""

#: boot-installer.xml:123
#, no-c-format
#. Tag: entry
msgid "cabriolet"
msgstr ""

#: boot-installer.xml:126
#, no-c-format
#. Tag: entry
msgid "dp264"
msgstr ""

#: boot-installer.xml:129
#, no-c-format
#. Tag: entry
msgid "eb164"
msgstr ""

#: boot-installer.xml:132
#, no-c-format
#. Tag: entry
msgid "eb64p"
msgstr ""

#: boot-installer.xml:135
#, no-c-format
#. Tag: entry
msgid "eb66"
msgstr ""

#: boot-installer.xml:138
#, no-c-format
#. Tag: entry
msgid "eb66p"
msgstr ""

#: boot-installer.xml:141
#, no-c-format
#. Tag: entry
msgid "jensen"
msgstr ""

#: boot-installer.xml:144
#, no-c-format
#. Tag: entry
msgid "lx164"
msgstr ""

#: boot-installer.xml:147
#, no-c-format
#. Tag: entry
msgid "miata"
msgstr ""

#: boot-installer.xml:150
#, no-c-format
#. Tag: entry
msgid "mikasa"
msgstr ""

#: boot-installer.xml:153
#, no-c-format
#. Tag: entry
msgid "mikasa-p"
msgstr ""

#: boot-installer.xml:156
#, no-c-format
#. Tag: entry
msgid "nautilus"
msgstr ""

#: boot-installer.xml:157
#, no-c-format
#. Tag: entry
msgid "ARC (see motherboard manual) or SRM"
msgstr ""

#: boot-installer.xml:159
#, no-c-format
#. Tag: entry
msgid "noname"
msgstr ""

#: boot-installer.xml:162
#, no-c-format
#. Tag: entry
msgid "noritake"
msgstr ""

#: boot-installer.xml:165
#, no-c-format
#. Tag: entry
msgid "noritake-p"
msgstr ""

#: boot-installer.xml:168
#, no-c-format
#. Tag: entry
msgid "pc164"
msgstr ""

#: boot-installer.xml:171
#, no-c-format
#. Tag: entry
msgid "rawhide"
msgstr ""

#: boot-installer.xml:174
#, no-c-format
#. Tag: entry
msgid "ruffian"
msgstr ""

#: boot-installer.xml:175 boot-installer.xml:190 boot-installer.xml:193
#, no-c-format
#. Tag: entry
msgid "ARC only"
msgstr ""

#: boot-installer.xml:177
#, no-c-format
#. Tag: entry
msgid "sable"
msgstr ""

#: boot-installer.xml:180
#, no-c-format
#. Tag: entry
msgid "sable-g"
msgstr ""

#: boot-installer.xml:183
#, no-c-format
#. Tag: entry
msgid "sx164"
msgstr ""

#: boot-installer.xml:186
#, no-c-format
#. Tag: entry
msgid "takara"
msgstr ""

#: boot-installer.xml:189
#, no-c-format
#. Tag: entry
msgid "<entry>xl</entry>"
msgstr ""

#: boot-installer.xml:192
#, no-c-format
#. Tag: entry
msgid "<entry>xlt</entry>"
msgstr ""

#: boot-installer.xml:200
#, no-c-format
#. Tag: para
msgid "Generally, none of these consoles can boot Linux directly, so the assistance of an intermediary bootloader is required. For the SRM console, <command>aboot</command>, a small, platform-independent bootloader, is used. See the (unfortunately outdated) <ulink url=\"&url-srm-howto;\">SRM HOWTO</ulink> for more information on <command>aboot</command>."
msgstr ""

#: boot-installer.xml:209
#, no-c-format
#. Tag: para
msgid "The following paragraphs are from the woody install manual, and are included here for reference; they may be useful to someone at a later date when Debian supports MILO-based installs again."
msgstr ""

#: boot-installer.xml:215
#, no-c-format
#. Tag: para
msgid "Generally, none of these consoles can boot Linux directly, so the assistance of an intermediary bootloader is required. There are two mainstream Linux loaders: <command>MILO</command> and <command>aboot</command>."
msgstr ""

#: boot-installer.xml:221
#, no-c-format
#. Tag: para
msgid "<command>MILO</command> is itself a console, which replaces ARC or SRM in memory. <command>MILO</command> can be booted from both ARC and SRM and is the only way to bootstrap Linux from the ARC console. <command>MILO</command> is platform-specific (a different <command>MILO</command> is needed for each system type) and exist only for those systems, for which ARC support is shown in the table above. See also the (unfortunately outdated) <ulink url=\"&url-milo-howto;\">MILO HOWTO</ulink>."
msgstr ""

#: boot-installer.xml:231
#, no-c-format
#. Tag: para
msgid "<command>aboot</command> is a small, platform-independent bootloader, which runs from SRM only. See the (also unfortunately outdated) <ulink url=\"&url-srm-howto;\">SRM HOWTO</ulink> for more information on <command>aboot</command>."
msgstr ""

#: boot-installer.xml:238
#, no-c-format
#. Tag: para
msgid ""
      "Thus, three scenarios are generally possible, depending on the system's console firmware and whether or not <command>MILO</command> is available: <informalexample><screen>\n"
      "SRM -&gt; aboot\n"
      "SRM -&gt; MILO\n"
      "ARC -&gt; MILO\n"
      "</screen></informalexample> Because <command>MILO</command> is not available for any of the Alpha systems currently in production (as of February 2000), and because it is no longer necessary to buy an OpenVMS or Tru64 Unix license to have SRM firmware on your older Alpha, it is recommended that you use SRM and <command>aboot</command> on new installations of GNU/Linux, unless you wish to dual-boot with Windows NT."
msgstr ""

#: boot-installer.xml:253
#, no-c-format
#. Tag: para
msgid "The majority of AlphaServers and all current server and workstation products contain both SRM and AlphaBIOS in their firmware. For <quote>half-flash</quote> machines such as the various evaluation boards, it is possible to switch from one version to another by reflashing the firmware. Also, once SRM is installed, it is possible to run ARC/AlphaBIOS from a floppy disk (using the <command>arc</command> command). For the reasons mentioned above, we recommend switching to SRM before installing &debian;."
msgstr ""

#: boot-installer.xml:264
#, no-c-format
#. Tag: para
msgid "As on other architectures, you should install the newest available revision of the firmware<footnote> <para> Except on Jensen, where Linux is not supported on firmware versions newer than 1.7 &mdash; see <ulink url=\"&url-jensen-howto;\"></ulink> for more information. </para> </footnote> before installing &debian;. For Alpha, firmware updates can be obtained from <ulink url=\"&url-alpha-firmware;\">Alpha Firmware Updates</ulink>."
msgstr ""

#: boot-installer.xml:283 boot-installer.xml:998 boot-installer.xml:1489 boot-installer.xml:1984 boot-installer.xml:2066 boot-installer.xml:2155 boot-installer.xml:2499 boot-installer.xml:2595
#, no-c-format
#. Tag: title
msgid "Booting with TFTP"
msgstr ""

#: boot-installer.xml:284
#, no-c-format
#. Tag: para
msgid ""
      "In SRM, Ethernet interfaces are named with the <userinput>ewa</userinput> prefix, and will be listed in the output of the <userinput>show dev</userinput> command, like this (edited slightly): <informalexample><screen>\n"
      "&gt;&gt;&gt; show dev\n"
      "ewa0.0.0.9.0               EWA0              08-00-2B-86-98-65\n"
      "ewb0.0.0.11.0              EWB0              08-00-2B-86-98-54\n"
      "ewc0.0.0.2002.0            EWC0              00-06-2B-01-32-B0\n"
      "</screen></informalexample> You first need to set the boot protocol: <informalexample><screen>\n"
      "&gt;&gt;&gt; set ewa0_protocol bootp\n"
      "</screen></informalexample> Then check the medium type is correct: <informalexample><screen>\n"
      "&gt;&gt;&gt; set ewa0_mode <replaceable>mode</replaceable>\n"
      "</screen></informalexample> You can get a listing of valid modes with <userinput>&gt;&gt;&gt;set ewa0_mode</userinput>."
msgstr ""

#: boot-installer.xml:302
#, no-c-format
#. Tag: para
msgid ""
      "Then, to boot from the first Ethernet interface, you would type: <informalexample><screen>\n"
      "&gt;&gt;&gt; boot ewa0 -flags \"\"\n"
      "</screen></informalexample> This will boot using the default kernel parameters as included in the netboot image."
msgstr ""

#: boot-installer.xml:311
#, no-c-format
#. Tag: para
msgid "If you wish to use a serial console, you <emphasis>must</emphasis> pass the <userinput>console=</userinput> parameter to the kernel. This can be done using the <userinput>-flags</userinput> argument to the SRM <userinput>boot</userinput> command. The serial ports are named the same as their corresponding files in <userinput>/dev</userinput>. Also, when specifying additional kernel parameters, you must repeat certain default options that are needed by the &d-i; images. For example, to boot from <userinput>ewa0</userinput> and use a console on the first serial port, you would type:"
msgstr ""

#: boot-installer.xml:323
#, no-c-format
#. Tag: screen
msgid "&gt;&gt;&gt; boot ewa0 -flags &quot;root=/dev/ram ramdisk_size=16384 console=ttyS0&quot;"
msgstr ""

#: boot-installer.xml:328
#, no-c-format
#. Tag: title
msgid "Booting from CD-ROM with the SRM Console"
msgstr ""

#: boot-installer.xml:329
#, no-c-format
#. Tag: para
msgid ""
      "Type <informalexample><screen>\n"
      "&gt;&gt;&gt; boot xxxx -flags 0\n"
      "</screen></informalexample> where <replaceable>xxxx</replaceable> is your CD-ROM drive in SRM notation."
msgstr ""

#: boot-installer.xml:341
#, no-c-format
#. Tag: title
msgid "Booting from CD-ROM with the ARC or AlphaBIOS Console"
msgstr ""

#: boot-installer.xml:342
#, no-c-format
#. Tag: para
msgid "To boot a CD-ROM from the ARC console, find your sub-architecture code name (see <xref linkend=\"alpha-cpus\"/>), then enter <filename>\\milo\\linload.exe</filename> as the boot loader and <filename>\\milo\\<replaceable>subarch</replaceable></filename> (where <replaceable>subarch</replaceable> is the proper subarchitecture name) as the OS Path in the `OS Selection Setup' menu. Ruffians make an exception: You need to use <filename>\\milo\\ldmilo.exe</filename> as boot loader."
msgstr ""

#: boot-installer.xml:358
#, no-c-format
#. Tag: title
msgid "Booting from Floppies with the SRM Console"
msgstr ""

#: boot-installer.xml:359
#, no-c-format
#. Tag: para
msgid ""
      "At the SRM prompt (<prompt>&gt;&gt;&gt;</prompt>), issue the following command: <informalexample><screen>\n"
      "&gt;&gt;&gt; boot dva0 -flags 0\n"
      "</screen></informalexample> possibly replacing <filename>dva0</filename> with the actual device name. Usually, <filename>dva0</filename> is the floppy; type <informalexample><screen>\n"
      "&gt;&gt;&gt; show dev\n"
      "</screen></informalexample> to see the list of devices (e.g., if you want to boot from a CD). Note that if you are booting via MILO, <command>-flags</command> argument is ignored, so you can just type <command>boot dva0</command>. If everything works OK, you will eventually see the Linux kernel boot."
msgstr ""

#: boot-installer.xml:376
#, no-c-format
#. Tag: para
msgid ""
      "If you want to specify kernel parameters when booting via <command>aboot</command>, use the following command: <informalexample><screen>\n"
      "&gt;&gt;&gt; boot dva0 -file linux.bin.gz -flags \"root=/dev/fd0 load_ramdisk=1 arguments\"\n"
      "</screen></informalexample> (typed on one line), substituting, if necessary, the actual SRM boot device name for <filename>dva0</filename>, the Linux boot device name for <filename>fd0</filename>, and the desired kernel parameters for <filename>arguments</filename>."
msgstr ""

#: boot-installer.xml:388
#, no-c-format
#. Tag: para
msgid "If you want to specify kernel parameters when booting via <command>MILO</command>, you will have to interrupt bootstrap once you get into MILO. See <xref linkend=\"booting-from-milo\"/>."
msgstr ""

#: boot-installer.xml:398
#, no-c-format
#. Tag: title
msgid "Booting from Floppies with the ARC or AlphaBIOS Console"
msgstr ""

#: boot-installer.xml:400
#, no-c-format
#. Tag: para
msgid "In the OS Selection menu, set <command>linload.exe</command> as the boot loader, and <command>milo</command> as the OS Path. Bootstrap using the newly created entry."
msgstr ""

#: boot-installer.xml:409
#, no-c-format
#. Tag: title
msgid "Booting with MILO"
msgstr ""

#: boot-installer.xml:410
#, no-c-format
#. Tag: para
msgid "MILO contained on the bootstrap media is configured to proceed straight to Linux automatically. Should you wish to intervene, all you need is to press space during MILO countdown."
msgstr ""

#: boot-installer.xml:416
#, no-c-format
#. Tag: para
msgid ""
      "If you want to specify all the bits explicitly (for example, to supply additional parameters), you can use a command like this: <informalexample><screen>\n"
      "MILO> boot fd0:linux.bin.gz root=/dev/fd0 load_ramdisk=1 <!-- arguments -->\n"
      "</screen></informalexample> If you are booting from something other than a floppy, substitute <filename>fd0</filename> in the above example with the appropriate device name in Linux notation. The <command>help</command> command would give you a brief MILO command reference."
msgstr ""

#: boot-installer.xml:435
#, no-c-format
#. Tag: title
msgid "Booting from TFTP"
msgstr ""

#: boot-installer.xml:441 boot-installer.xml:1004 boot-installer.xml:1507 boot-installer.xml:1990 boot-installer.xml:2505 boot-installer.xml:2601
#, no-c-format
#. Tag: para
msgid "Booting from the network requires that you have a network connection and a TFTP network boot server (DHCP, RARP, or BOOTP)."
msgstr ""

#: boot-installer.xml:446 boot-installer.xml:1009 boot-installer.xml:1512 boot-installer.xml:1995 boot-installer.xml:2510 boot-installer.xml:2606
#, no-c-format
#. Tag: para
msgid "Older systems such as the 715 might require the use of an RBOOT server instead of a BOOTP server."
msgstr ""

#: boot-installer.xml:451 boot-installer.xml:1014 boot-installer.xml:1517 boot-installer.xml:2000 boot-installer.xml:2515 boot-installer.xml:2611
#, no-c-format
#. Tag: para
msgid "The installation method to support network booting is described in <xref linkend=\"install-tftp\"/>."
msgstr ""

#: boot-installer.xml:459
#, no-c-format
#. Tag: title
msgid "Booting from TFTP on Netwinder"
msgstr ""

#: boot-installer.xml:460
#, no-c-format
#. Tag: para
msgid "Netwinders have two network interfaces: A 10Mbps NE2000-compatible card (which is generally referred to as <literal>eth0</literal>) and a 100Mbps Tulip card. There may be problems loading the image via TFTP using the 100Mbps card so it is recommended that you use the 10Mbps interface (the one labeled with <literal>10 Base-T</literal>)."
msgstr ""

#: boot-installer.xml:469
#, no-c-format
#. Tag: para
msgid "You need NeTTrom 2.2.1 or later to boot the installation system, and version 2.3.3 is recommended. Unfortunately, firmware files are currently not available for download because of license issues. If this situation changes, you may find new images at <ulink url=\"http//www.netwinder.org/\"></ulink>."
msgstr ""

#: boot-installer.xml:477
#, no-c-format
#. Tag: para
msgid ""
      "When you boot your Netwinder you have to interrupt the boot process during the countdown. This allows you to set a number of firmware settings needed in order to boot the installer. First of all, start by loading the default settings: <informalexample><screen>\n"
      "    NeTTrom command-&gt; load-defaults\n"
      "</screen></informalexample> Furthermore, you must configure the network, either with a static address: <informalexample><screen>\n"
      "    NeTTrom command-&gt; setenv netconfig_eth0 flash\n"
      "    NeTTrom command-&gt; setenv eth0_ip 192.168.0.10/24\n"
      "</screen></informalexample> where 24 is the number of set bits in the netmask, or a dynamic address: <informalexample><screen>\n"
      "    NeTTrom command-&gt; setenv netconfig_eth0 dhcp\n"
      "</screen></informalexample> You may also need to configure the <userinput>route1</userinput> settings if the TFTP server is not on the local subnet. Following these settings, you have to specify the TFTP server and the location of the image. You can then store your settings to flash. <informalexample><screen>\n"
      "    NeTTrom command-&gt; setenv kerntftpserver 192.168.0.1\n"
      "    NeTTrom command-&gt; setenv kerntftpfile boot.img\n"
      "    NeTTrom command-&gt; save-all\n"
      "</screen></informalexample> Now you have to tell the firmware that the TFTP image should be booted: <informalexample><screen>\n"
      "    NeTTrom command-&gt; setenv kernconfig tftp\n"
      "    NeTTrom command-&gt; setenv rootdev /dev/ram\n"
      "</screen></informalexample> If you use a serial console to install your Netwinder, you need to add the following setting: <informalexample><screen>\n"
      "    NeTTrom command-&gt; setenv cmdappend root=/dev/ram console=ttyS0,115200\n"
      "</screen></informalexample> Alternatively, for installations using a keyboard and monitor you have to set: <informalexample><screen>\n"
      "    NeTTrom command-&gt; setenv cmdappend root=/dev/ram\n"
      "</screen></informalexample> You can use the <command>printenv</command> command to review your environment settings. After you have verified that the settings are correct, you can load the image: <informalexample><screen>\n"
      "    NeTTrom command-&gt; boot\n"
      "</screen></informalexample> In case you run into any problems, a <ulink url=\"http://www.netwinder.org/howto/Firmware-HOWTO.html\">detailed HOWTO</ulink> is available."
msgstr ""

#: boot-installer.xml:529
#, no-c-format
#. Tag: title
msgid "Booting from TFTP on CATS"
msgstr ""

#: boot-installer.xml:530
#, no-c-format
#. Tag: para
msgid "On CATS machines, use <command>boot de0:</command> or similar at the Cyclone prompt."
msgstr ""

#: boot-installer.xml:540
#, no-c-format
#. Tag: title
msgid "Booting from CD-ROM"
msgstr ""

#: boot-installer.xml:546 boot-installer.xml:716 boot-installer.xml:1126 boot-installer.xml:1947 boot-installer.xml:2287 boot-installer.xml:2641
#, no-c-format
#. Tag: para
msgid "The easiest route for most people will be to use a set of Debian CDs. If you have a CD set, and if your machine supports booting directly off the CD, great! Simply <phrase arch=\"i386\"> configure your system for booting off a CD as described in <xref linkend=\"boot-dev-select\"/>, </phrase> insert your CD, reboot, and proceed to the next chapter."
msgstr ""

#: boot-installer.xml:557 boot-installer.xml:727 boot-installer.xml:1137 boot-installer.xml:1958 boot-installer.xml:2298 boot-installer.xml:2652
#, no-c-format
#. Tag: para
msgid "Note that certain CD drives may require special drivers, and thus be inaccessible in the early installation stages. If it turns out the standard way of booting off a CD doesn't work for your hardware, revisit this chapter and read about alternate kernels and installation methods which may work for you."
msgstr ""

#: boot-installer.xml:565 boot-installer.xml:735 boot-installer.xml:1145 boot-installer.xml:1966 boot-installer.xml:2306 boot-installer.xml:2660
#, no-c-format
#. Tag: para
msgid "Even if you cannot boot from CD-ROM, you can probably install the Debian system components and any packages you want from CD-ROM. Simply boot using a different media, such as floppies. When it's time to install the operating system, base system, and any additional packages, point the installation system at the CD-ROM drive."
msgstr ""

#: boot-installer.xml:573 boot-installer.xml:743 boot-installer.xml:1153 boot-installer.xml:1974 boot-installer.xml:2314 boot-installer.xml:2668
#, no-c-format
#. Tag: para
msgid "If you have problems booting, see <xref linkend=\"boot-troubleshooting\"/>."
msgstr ""

#: boot-installer.xml:580
#, no-c-format
#. Tag: para
msgid "To boot a CD-ROM from the Cyclone console prompt, use the command <command>boot cd0:cats.bin</command>"
msgstr ""

#: boot-installer.xml:589
#, no-c-format
#. Tag: title
msgid "Booting from Firmware"
msgstr ""

#: boot-installer.xml:595
#, no-c-format
#. Tag: para
msgid "There is an increasing number of consumer devices that directly boot from a flash chip on the device. The installer can be written to flash so it will automatically start when you reboot your machines."
msgstr ""

#: boot-installer.xml:601
#, no-c-format
#. Tag: para
msgid "In many cases, changing the firmware of an embedded device voids your warranty. Sometimes you are also not able to recover your device if there are problems during the flashing process. Therefore, please take care and follow the steps precisely."
msgstr ""

#: boot-installer.xml:612
#, no-c-format
#. Tag: title
msgid "Booting the NSLU2"
msgstr ""

#: boot-installer.xml:613
#, no-c-format
#. Tag: para
msgid "There are three ways how to put the installer firmware into flash:"
msgstr ""

#: boot-installer.xml:619
#, no-c-format
#. Tag: title
msgid "Using the NSLU2 web interface"
msgstr ""

#: boot-installer.xml:620
#, no-c-format
#. Tag: para
msgid "Go to the administration section and choose the menu item <literal>Upgrade</literal>. You can then browse your disk for the installer image you have previously downloaded. Then press the <literal>Start Upgrade</literal> button, confirm, wait for a few minutes and confirm again. The system will then boot straight into the installer."
msgstr ""

#: boot-installer.xml:631
#, no-c-format
#. Tag: title
msgid "Via the network using Linux/Unix"
msgstr ""

#: boot-installer.xml:632
#, no-c-format
#. Tag: para
msgid ""
      "You can use <command>upslug2</command> from any Linux or Unix machine to upgrade the machine via the network. This software is packaged for Debian. First, you have to put your NSLU2 in upgrade mode: <orderedlist> <listitem><para> Disconnect any disks and/or devices from the USB ports. </para></listitem> <listitem><para> Power off the NSLU2 </para></listitem> <listitem><para> Press and hold the reset button (accessible through the small hole on the back just above the power input). </para></listitem> <listitem><para> Press and release the power button to power on the NSLU2. </para></listitem> <listitem><para> Wait for 10 seconds watching the ready/status LED. After 10 seconds it will change from amber to red. Immediately release the reset button. </para></listitem> <listitem><para> The NSLU2 ready/status LED will flash alternately red/green (there is a 1 second delay before the first green). The NSLU2 is now in upgrade mode. </para></listitem> </orderedlist> See the <ulink url=\"http://www.nslu2-linux.org/wiki/OpenSlug/UsingTheBinary\">NSLU2-Linux pages</ulink> if you have problems with this. Once your NSLU2 is in upgrade mode, you can flash the new image: <informalexample><screen>\n"
      "sudo upslug2 -i di-nslu2.bin\n"
      "</screen></informalexample> Note that the tool also shows the MAC address of your NSLU2, which may come in handy to configure your DHCP server. After the whole image has been written and verified, the system will automatically reboot. Make sure you connect your USB disk again now, otherwise the installer won't be able to find it."
msgstr ""

#: boot-installer.xml:693
#, no-c-format
#. Tag: title
msgid "Via the network using Windows"
msgstr ""

#: boot-installer.xml:694
#, no-c-format
#. Tag: para
msgid "There is <ulink url=\"http://www.everbesthk.com/8-download/sercomm/firmware/all_router_utility.zip\">a tool</ulink> for Windows to upgrade the firmware via the network."
msgstr ""

#: boot-installer.xml:710 boot-installer.xml:1120 boot-installer.xml:1935 boot-installer.xml:2281 boot-installer.xml:2635
#, no-c-format
#. Tag: title
msgid "Booting from a CD-ROM"
msgstr ""

#: boot-installer.xml:848
#, no-c-format
#. Tag: title
msgid "Booting from Linux Using <command>LILO</command> or <command>GRUB</command>"
msgstr ""

#: boot-installer.xml:851
#, no-c-format
#. Tag: para
msgid "To boot the installer from hard disk, you must first download and place the needed files as described in <xref linkend=\"boot-drive-files\"/>."
msgstr ""

#: boot-installer.xml:856
#, no-c-format
#. Tag: para
msgid "If you intend to use the hard drive only for booting and then download everything over the network, you should download the <filename>netboot/debian-installer/i386/initrd.gz</filename> file and its corresponding kernel. This will allow you to repartition the hard disk from which you boot the installer, although you should do so with care."
msgstr ""

#: boot-installer.xml:864
#, no-c-format
#. Tag: para
msgid "Alternatively, if you intend to keep an existing partition on the hard drive unchanged during the install, you can download the <filename>hd-media/initrd.gz</filename> file and its kernel, as well as copy a CD iso to the drive (make sure the file is named ending in <literal>.iso</literal>). The installer can then boot from the drive and install from the CD image, without needing the network."
msgstr ""

#: boot-installer.xml:873
#, no-c-format
#. Tag: para
msgid "For <command>LILO</command>, you will need to configure two essential things in <filename>/etc/lilo.conf</filename>: <itemizedlist> <listitem><para> to load the <filename>initrd.gz</filename> installer at boot time; </para></listitem> <listitem><para> have the <filename>vmlinuz</filename> kernel use a RAM disk as its root partition. </para></listitem> </itemizedlist> Here is a <filename>/etc/lilo.conf</filename> example:"
msgstr ""

#: boot-installer.xml:894
#, no-c-format
#. Tag: screen
msgid ""
      "image=/boot/newinstall/vmlinuz\n"
      "       label=newinstall\n"
      "       initrd=/boot/newinstall/initrd.gz\n"
      "       root=/dev/ram0\n"
      "       append=\"ramdisk_size=12000\""
msgstr ""

#: boot-installer.xml:894
#, no-c-format
#. Tag: para
msgid "For more details, refer to the <citerefentry><refentrytitle>initrd</refentrytitle> <manvolnum>4</manvolnum></citerefentry> and <citerefentry><refentrytitle>lilo.conf</refentrytitle> <manvolnum>5</manvolnum></citerefentry> man pages. Now run <userinput>lilo</userinput> and reboot."
msgstr ""

#: boot-installer.xml:903
#, no-c-format
#. Tag: para
msgid ""
      "The procedure for <command>GRUB</command> is quite similar. Locate your <filename>menu.lst</filename> in the <filename>/boot/grub/</filename> directory (sometimes in the <filename>/boot/boot/grub/</filename>), add the following lines: <informalexample><screen>\n"
      "title  New Install\n"
      "kernel (hd0,0)/boot/newinstall/vmlinuz root=/dev/ram0 ramdisk_size=12000\n"
      "initrd (hd0,0)/boot/newinstall/initrd.gz\n"
      "</screen></informalexample> and reboot."
msgstr ""

#: boot-installer.xml:914
#, no-c-format
#. Tag: para
msgid "Note that the value of the <userinput>ramdisk_size</userinput> may need to be adjusted for the size of the initrd image. From here on, there should be no difference between <command>GRUB</command> or <command>LILO</command>."
msgstr ""

#: boot-installer.xml:925
#, no-c-format
#. Tag: title
msgid "Booting from USB Memory Stick"
msgstr ""

#: boot-installer.xml:926
#, no-c-format
#. Tag: para
msgid "Let's assume you have prepared everything from <xref linkend=\"boot-dev-select\"/> and <xref linkend=\"boot-usb-files\"/>. Now just plug your USB stick into some free USB connector and reboot the computer. The system should boot up, and you should be presented with the <prompt>boot:</prompt> prompt. Here you can enter optional boot arguments, or just hit &enterkey;."
msgstr ""

#: boot-installer.xml:939 boot-installer.xml:2047 boot-installer.xml:2541 boot-installer.xml:2689
#, no-c-format
#. Tag: title
msgid "Booting from Floppies"
msgstr ""

#: boot-installer.xml:940 boot-installer.xml:2549
#, no-c-format
#. Tag: para
msgid "You will have already downloaded the floppy images you needed and created floppies from the images in <xref linkend=\"create-floppy\"/>."
msgstr ""

#: boot-installer.xml:947
#, no-c-format
#. Tag: para
msgid "To boot from the installer boot floppy, place it in the primary floppy drive, shut down the system as you normally would, then turn it back on."
msgstr ""

#: boot-installer.xml:953
#, no-c-format
#. Tag: para
msgid "For installing from an LS-120 drive (ATAPI version) with a set of floppies, you need to specify the virtual location for the floppy device. This is done with the <emphasis>root=</emphasis> boot argument, giving the device that the ide-floppy driver maps the device to. For example, if your LS-120 drive is connected as the first IDE device (master) on the second cable, you enter <userinput>linux root=/dev/hdc</userinput> at the boot prompt. Installation from LS-120 is only supported by 2.4 and later kernels."
msgstr ""

#: boot-installer.xml:964
#, no-c-format
#. Tag: para
msgid "Note that on some machines, <keycombo><keycap>Control</keycap> <keycap>Alt</keycap> <keycap>Delete</keycap></keycombo> does not properly reset the machine, so a <quote>hard</quote> reboot is recommended. If you are installing from an existing operating system (e.g., from a DOS box) you don't have a choice. Otherwise, please do a hard reboot when booting."
msgstr ""

#: boot-installer.xml:973
#, no-c-format
#. Tag: para
msgid "The floppy disk will be accessed, and you should then see a screen that introduces the boot floppy and ends with the <prompt>boot:</prompt> prompt."
msgstr ""

#: boot-installer.xml:979
#, no-c-format
#. Tag: para
msgid "Once you press &enterkey;, you should see the message <computeroutput>Loading...</computeroutput>, followed by <computeroutput>Uncompressing Linux...</computeroutput>, and then a screenfull or so of information about the hardware in your system. More information on this phase of the boot process can be found below in <xref linkend=\"kernel-msgs\"/>."
msgstr ""

#: boot-installer.xml:988
#, no-c-format
#. Tag: para
msgid "After booting from the boot floppy, the root floppy is requested. Insert the root floppy and press &enterkey;, and the contents are loaded into memory. The installer program <command>debian-installer</command> is automatically launched."
msgstr ""

#: boot-installer.xml:1022
#, no-c-format
#. Tag: para
msgid "There are various ways to do a TFTP boot on i386."
msgstr ""

#: boot-installer.xml:1028
#, no-c-format
#. Tag: title
msgid "NIC or Motherboard that support PXE"
msgstr ""

#: boot-installer.xml:1029
#, no-c-format
#. Tag: para
msgid "It could be that your Network Interface Card or Motherboard provides PXE boot functionality. This is a <trademark class=\"trade\">Intel</trademark> re-implementation of TFTP boot. If so you may be able to configure your BIOS to boot from the network."
msgstr ""

#: boot-installer.xml:1040
#, no-c-format
#. Tag: title
msgid "NIC with Network BootROM"
msgstr ""

#: boot-installer.xml:1041
#, no-c-format
#. Tag: para
msgid "It could be that your Network Interface Card provides TFTP boot functionality."
msgstr ""

#: boot-installer.xml:1046
#, no-c-format
#. Tag: para
msgid "Let us (<email>&email-debian-boot-list;</email>) know how did you manage it. Please refer to this document."
msgstr ""

#: boot-installer.xml:1054
#, no-c-format
#. Tag: title
msgid "Etherboot"
msgstr ""

#: boot-installer.xml:1055
#, no-c-format
#. Tag: para
msgid "The <ulink url=\"http://www.etherboot.org\">etherboot project</ulink> provides bootdiskettes and even bootroms that do a TFTPboot."
msgstr ""

#: boot-installer.xml:1064
#, no-c-format
#. Tag: title
msgid "The Boot Prompt"
msgstr ""

#: boot-installer.xml:1065
#, no-c-format
#. Tag: para
msgid ""
      "When the installer boots, you should be presented with a friendly graphical screen showing the Debian logo and the boot prompt: <informalexample><screen>\n"
      "Press F1 for help, or ENTER to boot:\n"
      "</screen></informalexample> At the boot prompt you can either just press &enterkey; to boot the installer with default options or enter a specific boot method and, optionally, boot parameters."
msgstr ""

#: boot-installer.xml:1077
#, no-c-format
#. Tag: para
msgid "Information on available boot methods and on boot parameters which might be useful can be found by pressing <keycap>F2</keycap> through <keycap>F8</keycap>. If you add any parameters to the boot command line, be sure to type the boot method (the default is <userinput>linux</userinput>) and a space before the first parameter (e.g., <userinput>linux debconf/priority=medium</userinput>)."
msgstr ""

#: boot-installer.xml:1086
#, no-c-format
#. Tag: para
msgid "If you are installing the system via a remote management device that provides a text interface to the VGA console, you may not be able to see the initial graphical splash screen upon booting the installer; you may even not see the boot prompt. Examples of these devices include the text console of Compaq's <quote>integrated Lights Out</quote> (iLO) and HP's <quote>Integrated Remote Assistant</quote> (IRA). You can blindly press F1<footnote> <para> In some cases these devices will require special escape sequences to enact this keypress, for example the IRA uses <keycombo> <keycap>Ctrl</keycap> <keycap>F</keycap> </keycombo>,&nbsp;<keycap>1</keycap>. </para> </footnote> to bypass this screen and view the help text. Once you are past the splash screen and at the help text your keystrokes will be echoed at the prompt as expected. To prevent the installer from using the framebuffer for the rest of the installation, you will also want to add <userinput>debian-installer/framebuffer=false</userinput> to the boot prompt, as described in the help text."
msgstr ""

#: boot-installer.xml:1161
#, no-c-format
#. Tag: title
msgid "CD Contents"
msgstr ""

#: boot-installer.xml:1163
#, no-c-format
#. Tag: para
msgid "There are three basic variations of Debian Install CDs. The <emphasis>Business Card</emphasis> CD has a minimal installation that will fit on the small form factor CD media. It requires a network connection in order to install the rest of the base installation and make a usable system. The <emphasis>Network Install</emphasis> CD has all of the packages for a base install but requires a network connection to a Debian mirror site in order to install the extra packages one would want for a complete system . The set of Debian CDs can install a complete system from the wide range of packages without needing access to the network."
msgstr ""

#: boot-installer.xml:1179
#, no-c-format
#. Tag: para
msgid "The IA-64 architecture uses the next generation Extensible Firmware Interface (EFI) from Intel. Unlike the traditional x86 BIOS which knows little about the boot device other than the partition table and Master Boot Record (MBR), EFI can read and write files from FAT16 or FAT32 formatted disk partitions. This simplifies the often arcane process of starting a system. The system boot loader and the EFI firmware that supports it have a full filesystem to store the files necessary for booting the machine. This means that the system disk on an IA-64 system has an additional disk partition dedicated to EFI instead of the simple MBR or boot block on more conventional systems."
msgstr ""

#: boot-installer.xml:1195
#, no-c-format
#. Tag: para
msgid "The Debian Installer CD contains a small EFI partition where the <command>ELILO</command> bootloader, its configuration file, the installer's kernel, and initial filesystem (initrd) are located. The running system also contains an EFI partition where the necessary files for booting the system reside. These files are readable from the EFI Shell as described below."
msgstr ""

#: boot-installer.xml:1204
#, no-c-format
#. Tag: para
msgid "Most of the details of how <command>ELILO</command> actually loads and starts a system are transparent to the system installer. However, the installer must set up an EFI partition prior to installing the base system. Otherwise, the installation of <command>ELILO</command> will fail, rendering the system un-bootable. The EFI partition is allocated and formatted in the partitioning step of the installation prior to loading any packages on the system disk. The partitioning task also verifies that a suitable EFI partition is present before allowing the installation to proceed."
msgstr ""

#: boot-installer.xml:1216
#, no-c-format
#. Tag: para
msgid "The EFI Boot Manager is presented as the last step of the firmware initialization. It displays a menu list from which the user can select an option. Depending on the model of system and what other software has been loaded on the system, this menu may be different from one system to another. There should be at least two menu items displayed, <command>Boot Option Maintenance Menu</command> and <command>EFI Shell (Built-in)</command>. Using the first option is preferred, however, if that option is not available or the CD for some reason does not boot with it, use the second option."
msgstr ""

#: boot-installer.xml:1235
#, no-c-format
#. Tag: title
msgid "IMPORTANT"
msgstr ""

#: boot-installer.xml:1236
#, no-c-format
#. Tag: para
msgid "The EFI Boot Manager will select a default boot action, typically the first menu choice, within a pre-set number of seconds. This is indicated by a countdown at the bottom of the screen. Once the timer expires and the systems starts the default action, you may have to reboot the machine in order to continue the installation. If the default action is the EFI Shell, you can return to the Boot Manager by running <command>exit</command> at the shell prompt."
msgstr ""

#: boot-installer.xml:1248
#, no-c-format
#. Tag: title
msgid "Option 1: Booting from the Boot Option Maintenance Menu"
msgstr ""

#: boot-installer.xml:1255
#, no-c-format
#. Tag: para
msgid "Insert the CD in the DVD/CD drive and reboot the machine. The firmware will display the EFI Boot Manager page and menu after it completes its system initialization."
msgstr ""

#: boot-installer.xml:1261
#, no-c-format
#. Tag: para
msgid "Select <command>Boot Maintenance Menu</command> from the menu with the arrow keys and press <command>ENTER</command>. This will display a new menu."
msgstr ""

#: boot-installer.xml:1267
#, no-c-format
#. Tag: para
msgid "Select <command>Boot From a File</command> from the menu with the arrow keys and press <command>ENTER</command>. This will display a list of devices probed by the firmware. You should see two menu lines containing either the label <command>Debian Inst [Acpi ...</command> or <command>Removable Media Boot</command>. If you examine the rest of the menu line, you will notice that the device and controller information should be the same."
msgstr ""

#: boot-installer.xml:1278
#, no-c-format
#. Tag: para
msgid "You can choose either of the entries that refer to the CD/DVD drive. Select your choice with the arrow keys and press <command>ENTER</command>. If you choose <command>Removable Media Boot</command> the machine will immediately start the boot load sequence. If you choose <command>Debian Inst [Acpi ...</command> instead, it will display a directory listing of the bootable portion of the CD, requiring you to proceed to the next (additional) step."
msgstr ""

#: boot-installer.xml:1289
#, no-c-format
#. Tag: para
msgid "You will only need this step if you chose <command>Debian Inst [Acpi ...</command>. The directory listing will also show <command>[Treat like Removable Media Boot]</command> on the next to the last line. Select this line with the arrow keys and press <command>ENTER</command>. This will start the boot load sequence."
msgstr ""

#: boot-installer.xml:1301
#, no-c-format
#. Tag: para
msgid "These steps start the Debian boot loader which will display a menu page for you to select a boot kernel and options. Proceed to selecting the boot kernel and options."
msgstr ""

#: boot-installer.xml:1311
#, no-c-format
#. Tag: title
msgid "Option 2: Booting from the EFI Shell"
msgstr ""

#: boot-installer.xml:1312
#, no-c-format
#. Tag: para
msgid "If, for some reason, option 1 is not successful, reboot the machine and when the EFI Boot Manager screen appears there should be one option called <command>EFI Shell [Built-in]</command>. Boot the Debian Installer CD with the following steps:"
msgstr ""

#: boot-installer.xml:1323
#, no-c-format
#. Tag: para
msgid "Insert the CD in the DVD/CD drive and reboot the machine. The firmware will display the EFI Boot Manager page and menu after it completes system initialization."
msgstr ""

#: boot-installer.xml:1329
#, no-c-format
#. Tag: para
msgid "Select <command>EFI Shell</command> from the menu with the arrow keys and press <command>ENTER</command>. The EFI Shell will scan all of the bootable devices and display them to the console before displaying its command prompt. The recognized bootable partitions on devices will show a device name of <filename>fs<replaceable>n</replaceable>:</filename>. All other recognized partitions will be named <filename>blk<replaceable>n</replaceable>:</filename>. If you inserted the CD just before entering the shell, this may take a few extra seconds as it initializes the CD drive."
msgstr ""

#: boot-installer.xml:1343
#, no-c-format
#. Tag: para
msgid "Examine the output from the shell looking for the CDROM drive. It is most likely the <filename>fs0:</filename> device although other devices with bootable partitions will also show up as <filename>fs<replaceable>n</replaceable></filename>."
msgstr ""

#: boot-installer.xml:1350
#, no-c-format
#. Tag: para
msgid "Enter <command>fs<replaceable>n</replaceable>:</command> and press <command>ENTER</command> to select that device where <replaceable>n</replaceable> is the partition number for the CDROM. The shell will now display the partition number as its prompt."
msgstr ""

#: boot-installer.xml:1357
#, no-c-format
#. Tag: para
msgid "Enter <command>elilo</command> and press <command>ENTER</command>. This will start the boot load sequence."
msgstr ""

#: boot-installer.xml:1364
#, no-c-format
#. Tag: para
msgid "As with option 1, these steps start the Debian boot loader which will display a menu page for you to select a boot kernel and options. You can also enter the shorter <command>fs<replaceable>n</replaceable>:elilo</command> command at the shell prompt. Proceed to selecting the boot kernel and options."
msgstr ""

#: boot-installer.xml:1378
#, no-c-format
#. Tag: title
msgid "Installing using a Serial Console"
msgstr ""

#: boot-installer.xml:1380
#, no-c-format
#. Tag: para
msgid "You may choose to perform an install using a monitor and keyboard or using a serial connection. To use a monitor/keyboard setup, select an option containing the string [VGA console]. To install over a serial connection, choose an option containing the string [<replaceable>BAUD</replaceable> baud serial console], where <replaceable>BAUD</replaceable> is the speed of your serial console. Menu items for the most typical baud rate settings on the ttyS0 device are preconfigured."
msgstr ""

#: boot-installer.xml:1391
#, no-c-format
#. Tag: para
msgid "In most circumstances, you will want the installer to use the same baud rate as your connection to the EFI console. If you aren't sure what this setting is, you can obtain it using the command <command>baud</command> at the EFI shell."
msgstr ""

#: boot-installer.xml:1398
#, no-c-format
#. Tag: para
msgid "If there is not an option available that is configured for the serial device or baud rate you would like to use, you may override the console setting for one of the existing menu options. For example, to use a 57600 baud console over the ttyS1 device, enter <command>console=ttyS1,57600n8</command> into the <classname>Boot:</classname> text window."
msgstr ""

#: boot-installer.xml:1409
#, no-c-format
#. Tag: para
msgid "Most IA-64 boxes ship with a default console setting of 9600 baud. This setting is rather slow, and the normal installation process will take a significant time to draw each screen. You should consider either increasing the baud rate used for performing the installation, or performing a Text Mode installation. See the <classname>Params</classname> help menu for instructions on starting the installer in Text Mode."
msgstr ""

#: boot-installer.xml:1418
#, no-c-format
#. Tag: para
msgid "If you select the wrong console type, you will be able to select the kernel and enter parameters but both the display and your input will go dead as soon as the kernel starts, requiring you to reboot before you can begin the installation."
msgstr ""

#: boot-installer.xml:1427
#, no-c-format
#. Tag: title
msgid "Selecting the Boot Kernel and Options"
msgstr ""

#: boot-installer.xml:1429
#, no-c-format
#. Tag: para
msgid "The boot loader will display a form with a menu list and a text window with a <classname>Boot:</classname> prompt. The arrow keys select an item from the menu and any text typed at the keyboard will appear in the text window. There are also help screens which can be displayed by pressing the appropriate function key. The <classname>General</classname> help screen explains the menu choices and the <classname>Params</classname> screen explains the common command line options."
msgstr ""

#: boot-installer.xml:1441
#, no-c-format
#. Tag: para
msgid "Consult the <classname>General</classname> help screen for the description of the kernels and install modes most appropriate for your installation. You should also consult <xref linkend=\"boot-parms\"/> below for any additional parameters that you may want to set in the <classname>Boot:</classname> text window. The kernel version you choose selects the kernel version that will be used for both the installation process and the installed system. If you encounter kernel problems with the installation, you may also have those same problems with the system you install. The following two steps will select and start the install:"
msgstr ""

#: boot-installer.xml:1459
#, no-c-format
#. Tag: para
msgid "Select the kernel version and installation mode most appropriate to your needs with the arrow keys."
msgstr ""

#: boot-installer.xml:1464
#, no-c-format
#. Tag: para
msgid "Enter any boot parameters by typing at the keyboard. The text will be displayed directly in the text window. This is where kernel parameters (such as serial console settings) are specified."
msgstr ""

#: boot-installer.xml:1471
#, no-c-format
#. Tag: para
msgid "Press <command>ENTER</command>. This will load and start the kernel. The kernel will display its usual initialization messages followed by the first screen of the Debian Installer."
msgstr ""

#: boot-installer.xml:1480
#, no-c-format
#. Tag: para
msgid "Proceed to the next chapter to continue the installation where you will set up the language locale, network, and disk partitions."
msgstr ""

#: boot-installer.xml:1491
#, no-c-format
#. Tag: para
msgid "Booting an IA64 system from the network is similar to a CD boot. The only difference is how the installation kernel is loaded. The EFI Boot Manager can load and start programs from a server on the network. Once the installation kernel is loaded and starts, the system install will proceed thru the same steps as the CD install with the exception that the packages of the base install will be loaded from the network rather than the CD drive."
msgstr ""

#: boot-installer.xml:1525
#, no-c-format
#. Tag: para
msgid "Network booting an ia64 system requires two architecture-specific actions. On the boot server, DHCP and TFTP must be configured to deliver <command>elilo</command>. On the client a new boot option must be defined in the EFI boot manager to enable loading over a network."
msgstr ""

#: boot-installer.xml:1536
#, no-c-format
#. Tag: title
msgid "Configuring the Server"
msgstr ""

#: boot-installer.xml:1537
#, no-c-format
#. Tag: para
msgid ""
      "A suitable TFTP entry for network booting an ia64 system looks something like this: <informalexample><screen>\n"
      "host mcmuffin {\n"
      "        hardware ethernet 00:30:6e:1e:0e:83;\n"
      "        fixed-address 10.0.0.21;\n"
      "        filename \"debian-installer/ia64/elilo.efi\";\n"
      "}\n"
      "</screen></informalexample> Note that the goal is to get <command>elilo.efi</command> running on the client."
msgstr ""

#: boot-installer.xml:1547
#, no-c-format
#. Tag: para
msgid "Extract the <filename>netboot.tar.gz</filename> file into the directory used as the root for your tftp server. Typical tftp root directories include <filename>/var/lib/tftp</filename> and <filename>/tftpboot</filename>. This will create a <filename>debian-installer</filename> directory tree containing the boot files for an IA-64 system."
msgstr ""

#: boot-installer.xml:1557
#, no-c-format
#. Tag: screen
msgid ""
      "# cd /var/lib/tftp\n"
      "# tar xvfz /home/user/netboot.tar.gz\n"
      "./\n"
      "./debian-installer/\n"
      "./debian-installer/ia64/\n"
      "[...]"
msgstr ""

#: boot-installer.xml:1557
#, no-c-format
#. Tag: para
msgid "The <filename>netboot.tar.gz</filename> contains an <filename>elilo.conf</filename> file that should work for most configurations. However, should you need to make changes to this file, you can find it in the <filename>debian-installer/ia64/</filename> directory. It is possible to have different config files for different clients by naming them using the client's IP address in hex with the suffix <filename>.conf</filename> instead of <filename>elilo.conf</filename>. See documentation provided in the <classname>elilo</classname> package for details."
msgstr ""

#: boot-installer.xml:1574
#, no-c-format
#. Tag: title
msgid "Configuring the Client"
msgstr ""

#: boot-installer.xml:1575
#, no-c-format
#. Tag: para
msgid "To configure the client to support TFTP booting, start by booting to EFI and entering the <guimenu>Boot Option Maintenance Menu</guimenu>. <itemizedlist> <listitem><para> Add a boot option. </para></listitem> <listitem><para> You should see one or more lines with the text <guimenuitem>Load File [Acpi()/.../Mac()]</guimenuitem>. If more than one of these entries exist, choose the one containing the MAC address of the interface from which you'll be booting. Use the arrow keys to highlight your choice, then press enter. </para></listitem> <listitem><para> Name the entry <userinput>Netboot</userinput> or something similar, save, and exit back to the boot options menu. </para></listitem> </itemizedlist> You should see the new boot option you just created, and selecting it should initiate a DHCP query, leading to a TFTP load of <filename>elilo.efi</filename> from the server."
msgstr ""

#: boot-installer.xml:1607
#, no-c-format
#. Tag: para
msgid "The boot loader will display its prompt after it has downloaded and processed its configuration file. At this point, the installation proceeds with the same steps as a CD install. Select a boot option as in above and when the kernel has completed installing itself from the network, it will start the Debian Installer."
msgstr ""

#: boot-installer.xml:1616
#, no-c-format
#. Tag: para
msgid "Proceed to the next chapter to continue the installation where you will set up the language locale, network, and the disk partitions."
msgstr ""

#: boot-installer.xml:1629
#, no-c-format
#. Tag: title
msgid "Choosing an Installation Method"
msgstr ""

#: boot-installer.xml:1631
#, no-c-format
#. Tag: para
msgid "Some &arch-title; subarchs have the option of booting using either a 2.4.x or 2.2.x linux kernel. When such a choice exists, try the 2.4.x linux kernel. The installer should also require less memory when using a 2.4.x linux kernel as 2.2.x support requires a fixed-sized ramdisk and 2.4.x uses tmpfs."
msgstr ""

#: boot-installer.xml:1639
#, no-c-format
#. Tag: para
msgid "If you are using a 2.2.x linux kernel, then you need to use the &ramdisksize; kernel parameter."
msgstr ""

#: boot-installer.xml:1644
#, no-c-format
#. Tag: para
msgid "Make sure <userinput>root=/dev/ram</userinput> is one of your kernel parameters."
msgstr ""

#: boot-installer.xml:1649
#, no-c-format
#. Tag: para
msgid "If you're having trouble, check <ulink url=\"&url-m68k-cts-faq;\">cts's &arch-title; debian-installer FAQ</ulink>."
msgstr ""

#: boot-installer.xml:1666
#, no-c-format
#. Tag: title
msgid "Amiga"
msgstr ""

#: boot-installer.xml:1667
#, no-c-format
#. Tag: para
msgid "The only method of installation available to amiga is the hard drive (see <xref linkend=\"m68k-boot-hd\"/>). <emphasis>In other words the cdrom is not bootable.</emphasis>"
msgstr ""

#: boot-installer.xml:1673
#, no-c-format
#. Tag: para
msgid "Amiga does not currently work with bogl, so if you are seeing bogl errors, you need to include the kernel parameter <userinput>debian-installer/framebuffer=false</userinput>."
msgstr ""

#: boot-installer.xml:1682
#, no-c-format
#. Tag: title
msgid "Atari"
msgstr ""

#: boot-installer.xml:1683
#, no-c-format
#. Tag: para
msgid "The installer for atari may be started from either the hard drive (see <xref linkend=\"m68k-boot-hd\"/>) or from floppies (see <xref linkend=\"boot-from-floppies\"/>). <emphasis>In other words the cdrom is not bootable.</emphasis>"
msgstr ""

#: boot-installer.xml:1690
#, no-c-format
#. Tag: para
msgid "Atari does not currently work with bogl, so if you are seeing bogl errors, you need to include the kernel parameter <userinput>debian-installer/framebuffer=false</userinput>."
msgstr ""

#: boot-installer.xml:1699
#, no-c-format
#. Tag: title
msgid "BVME6000"
msgstr ""

#: boot-installer.xml:1700
#, no-c-format
#. Tag: para
msgid "The installer for BVME6000 may be started from a cdrom (see <xref linkend=\"m68k-boot-cdrom\"/>), floppies (see <xref linkend=\"boot-from-floppies\"/>), or the net (see <xref linkend=\"boot-tftp\"/>)."
msgstr ""

#: boot-installer.xml:1710
#, no-c-format
#. Tag: title
msgid "Macintosh"
msgstr ""

#: boot-installer.xml:1711
#, no-c-format
#. Tag: para
msgid "The only method of installation available to mac is from the hard drive (see <xref linkend=\"m68k-boot-hd\"/>). <emphasis>In other words the cdrom is not bootable.</emphasis> Macs do not have a working 2.4.x kernel."
msgstr ""

#: boot-installer.xml:1718
#, no-c-format
#. Tag: para
msgid "If your hardware uses a 53c9x-based scsi bus, then you may need to include the kernel parameter <userinput>mac53c9x=1,0</userinput>. Hardware with two such scsi buses, such as the Quadra 950, will need <userinput>mac53c9x=2,0</userinput> instead. Alternatively, the parameter can be specified as <userinput>mac53c9x=-1,0</userinput> which will leave autodetection on, but which will disable SCSI disconnects. Note that specifying this parameter is only necessary if you have more than one hard disk; otherwise, the system will run faster if you do not specify it."
msgstr ""

#: boot-installer.xml:1733
#, no-c-format
#. Tag: title
msgid "MVME147 and MVME16x"
msgstr ""

#: boot-installer.xml:1734
#, no-c-format
#. Tag: para
msgid "The installer for MVME147 and MVME16x may be started from either floppies (see <xref linkend=\"boot-from-floppies\"/>) or the net (see <xref linkend=\"boot-tftp\"/>). <emphasis>In other words the cdrom is not bootable.</emphasis>"
msgstr ""

#: boot-installer.xml:1744
#, no-c-format
#. Tag: title
msgid "Q40/Q60"
msgstr ""

#: boot-installer.xml:1745
#, no-c-format
#. Tag: para
msgid "The only method of installation available to Q40/Q60 is from the hard drive (see <xref linkend=\"m68k-boot-hd\"/>). <emphasis>In other words the cdrom is not bootable.</emphasis>"
msgstr ""

#: boot-installer.xml:1756
#, no-c-format
#. Tag: title
msgid "Booting from a Hard Disk"
msgstr ""

#: boot-installer.xml:1762 boot-installer.xml:2360
#, no-c-format
#. Tag: para
msgid "Booting from an existing operating system is often a convenient option; for some systems it is the only supported method of installation."
msgstr ""

#: boot-installer.xml:1768 boot-installer.xml:2366
#, no-c-format
#. Tag: para
msgid "To boot the installer from hard disk, you will have already completed downloading and placing the needed files in <xref linkend=\"boot-drive-files\"/>."
msgstr ""

#: boot-installer.xml:1777
#, no-c-format
#. Tag: para
msgid "At least six different ramdisks may be used to boot from the hard drive, three different types each with and without support for a 2.2.x linux kernel (see <ulink url=\"&disturl;/main/installer-&architecture;/current/images/MANIFEST\">MANIFEST</ulink> for details)."
msgstr ""

#: boot-installer.xml:1785
#, no-c-format
#. Tag: para
msgid "The three different types of ramdisks are <filename>cdrom</filename>, <filename>hd-media</filename>, and <filename>nativehd</filename>. These ramdisks differ only in their source for installation packages. The <filename>cdrom</filename> ramdisk uses a cdrom to get debian-installer packages. The <filename>hd-media</filename> ramdisk uses an iso image file of a cdrom currently residing on a hard disk. Finally, the <filename>nativehd</filename> ramdisk uses the net to install packages."
msgstr ""

#: boot-installer.xml:1806
#, no-c-format
#. Tag: title
msgid "Booting from AmigaOS"
msgstr ""

#: boot-installer.xml:1807
#, no-c-format
#. Tag: para
msgid "In the <command>Workbench</command>, start the Linux installation process by double-clicking on the <guiicon>StartInstall</guiicon> icon in the <filename>debian</filename> directory."
msgstr ""

#: boot-installer.xml:1813
#, no-c-format
#. Tag: para
msgid "You may have to press the &enterkey; key twice after the Amiga installer program has output some debugging information into a window. After this, the screen will go grey, there will be a few seconds' delay. Next, a black screen with white text should come up, displaying all kinds of kernel debugging information. These messages may scroll by too fast for you to read, but that's OK. After a couple of seconds, the installation program should start automatically, so you can continue down at <xref linkend=\"d-i-intro\"/>."
msgstr ""

#: boot-installer.xml:1828
#, no-c-format
#. Tag: title
msgid "Booting from Atari TOS"
msgstr ""

#: boot-installer.xml:1829
#, no-c-format
#. Tag: para
msgid "At the GEM desktop, start the Linux installation process by double-clicking on the <guiicon>bootstra.prg</guiicon> icon in the <filename>debian</filename> directory and clicking <guibutton>Ok</guibutton> at the program options dialog box."
msgstr ""

#: boot-installer.xml:1836
#, no-c-format
#. Tag: para
msgid "You may have to press the &enterkey; key after the Atari bootstrap program has output some debugging information into a window. After this, the screen will go grey, there will be a few seconds' delay. Next, a black screen with white text should come up, displaying all kinds of kernel debugging information. These messages may scroll by too fast for you to read, but that's OK. After a couple of seconds, the installation program should start automatically, so you can continue below at <xref linkend=\"d-i-intro\"/>."
msgstr ""

#: boot-installer.xml:1851
#, no-c-format
#. Tag: title
msgid "Booting from MacOS"
msgstr ""

#: boot-installer.xml:1852
#, no-c-format
#. Tag: para
msgid "You must retain the original Mac system and boot from it. It is <emphasis>essential</emphasis> that, when booting MacOS in preparation for booting the Penguin linux loader, you hold the <keycap>shift</keycap> key down to prevent extensions from loading. If you don't use MacOS except for loading linux, you can accomplish the same thing by removing all extensions and control panels from the Mac's System Folder. Otherwise extensions may be left running and cause random problems with the running linux kernel."
msgstr ""

#: boot-installer.xml:1863
#, no-c-format
#. Tag: para
msgid "Macs require the <command>Penguin</command> bootloader. If you do not have the tools to handle a <command>Stuffit</command> archive, &penguin19.hfs; is an hfs disk image with <command>Penguin</command> unpacked. <xref linkend=\"create-floppy\"/> describes how to copy this image to a floppy."
msgstr ""

#: boot-installer.xml:1872
#, no-c-format
#. Tag: para
msgid "At the MacOS desktop, start the Linux installation process by double-clicking on the <guiicon>Penguin Prefs</guiicon> icon in the <filename>Penguin</filename> directory. The <command>Penguin</command> booter will start up. Go to the <guimenuitem>Settings</guimenuitem> item in the <guimenu>File</guimenu> menu, click the <guilabel>Kernel</guilabel> tab. Select the kernel (<filename>vmlinuz</filename>) and ramdisk (<filename>initrd.gz</filename>) images in the <filename>install</filename> directory by clicking on the corresponding buttons in the upper right corner, and navigating the file select dialogs to locate the files."
msgstr ""

#: boot-installer.xml:1887
#, no-c-format
#. Tag: para
msgid "To set the boot parameters in Penguin, choose <guimenu>File</guimenu> -&gt; <guimenuitem>Settings...</guimenuitem>, then switch to the <guilabel>Options</guilabel> tab. Boot parameters may be typed in to the text entry area. If you will always want to use these settings, select <guimenu>File</guimenu> -&gt; <guimenuitem>Save Settings as Default</guimenuitem>."
msgstr ""

#: boot-installer.xml:1896
#, no-c-format
#. Tag: para
msgid "Close the <guilabel>Settings</guilabel> dialog, save the settings and start the bootstrap using the <guimenuitem>Boot Now</guimenuitem> item in the <guimenu>File</guimenu> menu."
msgstr ""

#: boot-installer.xml:1903
#, no-c-format
#. Tag: para
msgid "The <command>Penguin</command> booter will output some debugging information into a window. After this, the screen will go grey, there will be a few seconds' delay. Next, a black screen with white text should come up, displaying all kinds of kernel debugging information. These messages may scroll by too fast for you to read, but that's OK. After a couple of seconds, the installation program should start automatically, so you can continue below at <xref linkend=\"d-i-intro\"/>."
msgstr ""

#: boot-installer.xml:1918
#, no-c-format
#. Tag: title
msgid "Booting from Q40/Q60"
msgstr ""

#: boot-installer.xml:1920
#, no-c-format
#. Tag: para
msgid "FIXME"
msgstr ""

#: boot-installer.xml:1924
#, no-c-format
#. Tag: para
msgid "The installation program should start automatically, so you can continue below at <xref linkend=\"d-i-intro\"/>."
msgstr ""

#: boot-installer.xml:1936
#, no-c-format
#. Tag: para
msgid "Currently, the only &arch-title; subarchitecture that supports CD-ROM booting is the BVME6000."
msgstr ""

#: boot-installer.xml:2008
#, no-c-format
#. Tag: para
msgid "After booting the VMEbus systems you will be presented with the LILO <prompt>Boot:</prompt> prompt. At that prompt enter one of the following to boot Linux and begin installation proper of the Debian software using vt102 terminal emulation:"
msgstr ""

#: boot-installer.xml:2019
#, no-c-format
#. Tag: para
msgid "type <screen>i6000 &enterkey;</screen> to install a BVME4000/6000"
msgstr ""

#: boot-installer.xml:2024
#, no-c-format
#. Tag: para
msgid "type <screen>i162 &enterkey;</screen> to install an MVME162"
msgstr ""

#: boot-installer.xml:2029
#, no-c-format
#. Tag: para
msgid "type <screen>i167 &enterkey;</screen> to install an MVME166/167"
msgstr ""

#: boot-installer.xml:2036
#, no-c-format
#. Tag: para
msgid "You may additionally append the string <screen>TERM=vt100</screen> to use vt100 terminal emulation, e.g., <screen>i6000 TERM=vt100 &enterkey;</screen>."
msgstr ""

#: boot-installer.xml:2048
#, no-c-format
#. Tag: para
msgid "For most &arch-title; architectures, booting from a local filesystem is the recommended method."
msgstr ""

#: boot-installer.xml:2053
#, no-c-format
#. Tag: para
msgid "Booting from the boot floppy is supported only for Atari and VME (with a SCSI floppy drive on VME) at this time."
msgstr ""

#: boot-installer.xml:2069 boot-installer.xml:2116
#, no-c-format
#. Tag: title
msgid "SGI TFTP Booting"
msgstr ""

#: boot-installer.xml:2070
#, no-c-format
#. Tag: para
msgid ""
      "After entering the command monitor use <informalexample><screen>\n"
      "bootp():\n"
      "</screen></informalexample> on SGI machines to boot linux and to begin installation of the Debian Software. In order to make this work you may have to unset the <envar>netaddr</envar> environment variable. Type <informalexample><screen>\n"
      "unsetenv netaddr\n"
      "</screen></informalexample> in the command monitor to do this."
msgstr ""

#: boot-installer.xml:2089 boot-installer.xml:2138 boot-installer.xml:2193 boot-installer.xml:2232
#, no-c-format
#. Tag: title
msgid "Broadcom BCM91250A and BCM91480B TFTP Booting"
msgstr ""

#: boot-installer.xml:2090 boot-installer.xml:2194
#, no-c-format
#. Tag: para
msgid ""
      "On the Broadcom BCM91250A and BCM91480B evaluation boards, you have to load the SiByl boot loader via TFTP which will then load and start the Debian installer. In most cases, you will first obtain an IP address via DHCP but it is also possible to configure a static address. In order to use DHCP, you can enter the following command on the CFE prompt: <informalexample><screen>\n"
      "ifconfig eth0 -auto\n"
      "</screen></informalexample> Once you have obtained an IP address, you can load SiByl with the following command: <informalexample><screen>\n"
      "boot 192.168.1.1:/boot/sibyl\n"
      "</screen></informalexample> You need to substitute the IP address listed in this example with either the name or the IP address of your TFTP server. Once you issue this command, the installer will be loaded automatically."
msgstr ""

#: boot-installer.xml:2113 boot-installer.xml:2217 boot-installer.xml:2740
#, no-c-format
#. Tag: title
msgid "Boot Parameters"
msgstr ""

#: boot-installer.xml:2117
#, no-c-format
#. Tag: para
msgid "On SGI machines you can append boot parameters to the <command>bootp():</command> command in the command monitor."
msgstr ""

#: boot-installer.xml:2122
#, no-c-format
#. Tag: para
msgid ""
      "Following the <command>bootp():</command> command you can give the path and name of the file to boot if you did not give an explicit name via your bootp/dhcp server. Example: <informalexample><screen>\n"
      "bootp():/boot/tftpboot.img\n"
      "</screen></informalexample> Further kernel parameters can be passed via <command>append</command>:"
msgstr ""

#: boot-installer.xml:2132
#, no-c-format
#. Tag: screen
msgid "bootp(): append=\"root=/dev/sda1\""
msgstr ""

#: boot-installer.xml:2139 boot-installer.xml:2233
#, no-c-format
#. Tag: para
msgid "You cannot pass any boot parameters directly from the CFE prompt. Instead, you have to edit the <filename>/boot/sibyl.conf</filename> file on the TFTP server and add your parameters to the <replaceable>extra_args</replaceable> variable."
msgstr ""

#: boot-installer.xml:2158 boot-installer.xml:2220
#, no-c-format
#. Tag: title
msgid "Cobalt TFTP Booting"
msgstr ""

#: boot-installer.xml:2159
#, no-c-format
#. Tag: para
msgid "Strictly speaking, Cobalt does not use TFTP but NFS to boot. You need to install an NFS server and put the installer files in <filename>/nfsroot</filename>. When you boot your Cobalt, you have to press the left and the right cursor buttons at the same time and the machine will boot via the network from NFS. It will then display several options on the display. There are the following two installation methods:"
msgstr ""

#: boot-installer.xml:2169
#, no-c-format
#. Tag: para
msgid "Via SSH (default): In this case, the installer will configure the network via DHCP and start an SSH server. It will then display a random password and other login information (such as the IP address) on the Cobalt LCD. When you connect to the machine with an SSH client you can start with the installation."
msgstr ""

#: boot-installer.xml:2178
#, no-c-format
#. Tag: para
msgid "Via serial console: Using a null modem cable, you can connect to the serial port of your Cobalt machine (using 115200 bps) and perform the installation this way. This option is not available on Qube 2700 (Qube1) machines since they have no serial port."
msgstr ""

#: boot-installer.xml:2221
#, no-c-format
#. Tag: para
msgid "You cannot pass any boot parameters directly. Instead, you have to edit the <filename>/nfsroot/default.colo</filename> file on the NFS server and add your parameters to the <replaceable>args</replaceable> variable."
msgstr ""

#: boot-installer.xml:2249
#, no-c-format
#. Tag: title
msgid "s390 Limitations"
msgstr ""

#: boot-installer.xml:2250
#, no-c-format
#. Tag: para
msgid "In order to run the installation system a working network setup and ssh session is needed on S/390."
msgstr ""

#: boot-installer.xml:2255
#, no-c-format
#. Tag: para
msgid "The booting process starts with a network setup that prompts you for several network parameters. If the setup is successful, you will login to the system by starting a ssh session which will launch the standard installation system."
msgstr ""

#: boot-installer.xml:2266
#, no-c-format
#. Tag: title
msgid "s390 Boot Parameters"
msgstr ""

#: boot-installer.xml:2267
#, no-c-format
#. Tag: para
msgid "On S/390 you can append boot parameters in the parm file. This file can either be in ASCII or EBCDIC format. Please read <ulink url=\"&url-s390-devices;\">Device Drivers and Installation Commands</ulink> for more information about S/390-specific boot parameters."
msgstr ""

#: boot-installer.xml:2321
#, no-c-format
#. Tag: para
msgid "Currently, the only &arch-title; subarchitectures that support CD-ROM booting are PReP and New World PowerMacs. On PowerMacs, hold the <keycap>c</keycap> key, or else the combination of <keycap>Command</keycap>, <keycap>Option</keycap>, <keycap>Shift</keycap>, and <keycap>Delete</keycap> keys together while booting to boot from the CD-ROM."
msgstr ""

#: boot-installer.xml:2330
#, no-c-format
#. Tag: para
msgid "OldWorld PowerMacs will not boot a Debian CD, because OldWorld computers relied on a Mac OS ROM CD boot driver to be present on the CD, and a free-software version of this driver is not available. All OldWorld systems have floppy drives, so use the floppy drive to launch the installer, and then point the installer to the CD for the needed files."
msgstr ""

#: boot-installer.xml:2339
#, no-c-format
#. Tag: para
msgid "If your system doesn't boot directly from CD-ROM, you can still use the CD-ROM to install the system. On NewWorlds, you can also use an OpenFirmware command to boot from the CD-ROM manually. Follow the instructions in <xref linkend=\"boot-newworld\"/> for booting from the hard disk, except use the path to <command>yaboot</command> on the CD at the OF prompt, such as"
msgstr ""

#: boot-installer.xml:2348
#, no-c-format
#. Tag: screen
msgid "0 &gt; boot cd:,\\install\\yaboot"
msgstr ""

#: boot-installer.xml:2354
#, no-c-format
#. Tag: title
msgid "Booting from Hard Disk"
msgstr ""

#: boot-installer.xml:2375
#, no-c-format
#. Tag: title
msgid "Booting CHRP from OpenFirmware"
msgstr ""

#: boot-installer.xml:2379
#, no-c-format
#. Tag: emphasis
msgid "Not yet written."
msgstr ""

#: boot-installer.xml:2384
#, no-c-format
#. Tag: title
msgid "Booting OldWorld PowerMacs from MacOS"
msgstr ""

#: boot-installer.xml:2385
#, no-c-format
#. Tag: para
msgid "If you set up BootX in <xref linkend=\"files-oldworld\"/>, you can use it to boot into the installation system. Double click the <guiicon>BootX</guiicon> application icon. Click on the <guibutton>Options</guibutton> button and select <guilabel>Use Specified RAM Disk</guilabel>. This will give you the chance to select the <filename>ramdisk.image.gz</filename> file. You may need to select the <guilabel>No Video Driver</guilabel> checkbox, depending on your hardware. Then click the <guibutton>Linux</guibutton> button to shut down MacOS and launch the installer."
msgstr ""

#: boot-installer.xml:2403
#, no-c-format
#. Tag: title
msgid "Booting NewWorld Macs from OpenFirmware"
msgstr ""

#: boot-installer.xml:2404
#, no-c-format
#. Tag: para
msgid ""
      "You will have already placed the <filename>vmlinux</filename>, <filename>initrd.gz</filename>, <filename>yaboot</filename>, and <filename>yaboot.conf</filename> files at the root level of your HFS partition in <xref linkend=\"files-newworld\"/>. Restart the computer, and immediately (during the chime) hold down the <keycap>Option</keycap>, <keycap>Command (cloverleaf/Apple)</keycap>, <keycap>o</keycap>, and <keycap>f</keycap> keys all together. After a few seconds you will be presented with the Open Firmware prompt. At the prompt, type <informalexample><screen>\n"
      "0 &gt; boot hd:<replaceable>x</replaceable>,yaboot\n"
      "</screen></informalexample> replacing <replaceable>x</replaceable> with the partition number of the HFS partition where the kernel and yaboot files were placed, followed by a &enterkey;. On some machines, you may need to use <userinput>ide0:</userinput> instead of <userinput>hd:</userinput>. In a few more seconds you will see a yaboot prompt <informalexample><screen>\n"
      "boot:\n"
      "</screen></informalexample> At yaboot's <prompt>boot:</prompt> prompt, type either <userinput>install</userinput> or <userinput>install video=ofonly</userinput> followed by a &enterkey;. The <userinput>video=ofonly</userinput> argument is for maximum compatibility; you can try it if <userinput>install</userinput> doesn't work. The Debian installation program should start."
msgstr ""

#: boot-installer.xml:2439
#, no-c-format
#. Tag: title
msgid "Booting from USB memory stick"
msgstr ""

#: boot-installer.xml:2440
#, no-c-format
#. Tag: para
msgid "Currently, NewWorld PowerMac systems are known to support USB booting."
msgstr ""

#: boot-installer.xml:2446
#, no-c-format
#. Tag: para
msgid "Make sure you have prepared everything from <xref linkend=\"boot-usb-files\"/>. To boot a Macintosh system from a USB stick, you will need to use the Open Firmware prompt, since Open Firmware does not search USB storage devices by default. To get to the prompt, hold down <keycombo><keycap>Command</keycap> <keycap>Option</keycap> <keycap>o</keycap> <keycap>f</keycap></keycombo> all together while booting (see <xref linkend=\"invoking-openfirmware\"/>)."
msgstr ""

#: boot-installer.xml:2458
#, no-c-format
#. Tag: para
msgid "You will need to work out where the USB storage device appears in the device tree, since at the moment <command>ofpath</command> cannot work that out automatically. Type <userinput>dev / ls</userinput> and <userinput>devalias</userinput> at the Open Firmware prompt to get a list of all known devices and device aliases. On the author's system with various types of USB stick, paths such as <filename>usb0/disk</filename>, <filename>usb0/hub/disk</filename>, <filename>/pci@f2000000/usb@1b,1/disk@1</filename>, and <filename>/pci@f2000000/usb@1b,1/hub@1/disk@1</filename> work."
msgstr ""

#: boot-installer.xml:2470
#, no-c-format
#. Tag: para
msgid ""
      "Having worked out the device path, use a command like this to boot the installer: <informalexample><screen>\n"
      "boot <replaceable>usb0/disk</replaceable>:<replaceable>2</replaceable>,\\\\:tbxi\n"
      "</screen></informalexample> The <replaceable>2</replaceable> matches the Apple_HFS or Apple_Bootstrap partition onto which you copied the boot image earlier, and the <userinput>,\\\\:tbxi</userinput> part instructs Open Firmware to boot from the file with an HFS file type of \"tbxi\" (i.e. <command>yaboot</command>) in the directory previously blessed with <command>hattrib -b</command>."
msgstr ""

#: boot-installer.xml:2484
#, no-c-format
#. Tag: para
msgid "The system should now boot up, and you should be presented with the <prompt>boot:</prompt> prompt. Here you can enter optional boot arguments, or just hit &enterkey;."
msgstr ""

#: boot-installer.xml:2490
#, no-c-format
#. Tag: para
msgid "This boot method is new, and may be difficult to get to work on some NewWorld systems. If you have problems, please file an installation report, as explained in <xref linkend=\"submit-bug\"/>."
msgstr ""

#: boot-installer.xml:2523
#, no-c-format
#. Tag: para
msgid "Currently, PReP and New World PowerMac systems support netbooting."
msgstr ""

#: boot-installer.xml:2527
#, no-c-format
#. Tag: para
msgid "On machines with Open Firmware, such as NewWorld Power Macs, enter the boot monitor (see <xref linkend=\"invoking-openfirmware\"/>) and use the command <command>boot enet:0</command>. PReP and CHRP boxes may have different ways of addressing the network. On a PReP machine, you should try <userinput>boot <replaceable>server_ipaddr</replaceable>,<replaceable>file</replaceable>,<replaceable>client_ipaddr</replaceable></userinput>."
msgstr ""

#: boot-installer.xml:2542
#, no-c-format
#. Tag: para
msgid "Booting from floppies is supported for &arch-title;, although it is generally only applicable for OldWorld systems. NewWorld systems are not equipped with floppy drives, and attached USB floppy drives are not supported for booting."
msgstr ""

#: boot-installer.xml:2554
#, no-c-format
#. Tag: para
msgid "To boot from the <filename>boot-floppy-hfs.img</filename> floppy, place it in floppy drive after shutting the system down, and before pressing the power-on button."
msgstr ""

#: boot-installer.xml:2560
#, no-c-format
#. Tag: para
msgid "For those not familiar with Macintosh floppy operations: a floppy placed in the machine prior to boot will be the first priority for the system to boot from. A floppy without a valid boot system will be ejected, and the machine will then check for bootable hard disk partitions."
msgstr ""

#: boot-installer.xml:2567
#, no-c-format
#. Tag: para
msgid "After booting, the <filename>root.bin</filename> floppy is requested. Insert the root floppy and press &enterkey;. The installer program is automatically launched after the root system has been loaded into memory."
msgstr ""

#: boot-installer.xml:2578
#, no-c-format
#. Tag: title
msgid "PowerPC Boot Parameters"
msgstr ""

#: boot-installer.xml:2579
#, no-c-format
#. Tag: para
msgid "Many older Apple monitors used a 640x480 67Hz mode. If your video appears skewed on an older Apple monitor, try appending the boot argument <userinput>video=atyfb:vmode:6</userinput> , which will select that mode for most Mach64 and Rage video hardware. For Rage 128 hardware, this changes to <userinput>video=aty128fb:vmode:6</userinput> ."
msgstr ""

#: boot-installer.xml:2619
#, no-c-format
#. Tag: para
msgid "On machines with OpenBoot, simply enter the boot monitor on the machine which is being installed (see <xref linkend=\"invoking-openboot\"/>). Use the command <userinput>boot net</userinput> to boot from a TFTP and RARP server, or try <userinput>boot net:bootp</userinput> or <userinput>boot net:dhcp</userinput> to boot from a TFTP and BOOTP or DHCP server. Some older OpenBoot revisions require using the device name, such as <userinput>boot le()</userinput>; these probably don't support BOOTP nor DHCP."
msgstr ""

#: boot-installer.xml:2675
#, no-c-format
#. Tag: para
msgid "Most OpenBoot versions support the <userinput>boot cdrom</userinput> command which is simply an alias to boot from the SCSI device on ID 6 (or the secondary master for IDE based systems). You may have to use the actual device name for older OpenBoot versions that don't support this special command. Note that some problems have been reported on Sun4m (e.g., Sparc 10s and Sparc 20s) systems booting from CD-ROM."
msgstr ""

#: boot-installer.xml:2690
#, no-c-format
#. Tag: para
msgid ""
      "To boot from floppy on a Sparc, use <informalexample><screen>\n"
      "Stop-A -&gt; OpenBoot: \"boot floppy\"\n"
      "</screen></informalexample> Be warned that the newer Sun4u (ultra) architecture does not support floppy booting. A typical error message is <computeroutput>Bad magic number in disk label - Can't open disk label package</computeroutput>. Furthermore, a number of Sun4c models (such as the IPX) do not support the compressed images found on the disks, so also are not supported."
msgstr ""

#: boot-installer.xml:2702
#, no-c-format
#. Tag: para
msgid "Several Sparcs (e.g. Ultra 10) have an OBP bug that prevents them from booting (instead of not supporting booting at all). The appropriate OBP update can be downloaded as product ID 106121 from <ulink url=\"http://sunsolve.sun.com\"></ulink>."
msgstr ""

#: boot-installer.xml:2709
#, no-c-format
#. Tag: para
msgid ""
      "If you are booting from the floppy, and you see messages such as <informalexample><screen>\n"
      "Fatal error: Cannot read partition\n"
      "Illegal or malformed device name\n"
      "</screen></informalexample> then it is possible that floppy booting is simply not supported on your machine."
msgstr ""

#: boot-installer.xml:2721
#, no-c-format
#. Tag: title
msgid "IDPROM Messages"
msgstr ""

#: boot-installer.xml:2722
#, no-c-format
#. Tag: para
msgid "If you cannot boot because you get messages about a problem with <quote>IDPROM</quote>, then it's possible that your NVRAM battery, which holds configuration information for you firmware, has run out. See the <ulink url=\"&url-sun-nvram-faq;\">Sun NVRAM FAQ</ulink> for more information."
msgstr ""

#: boot-installer.xml:2741
#, no-c-format
#. Tag: para
msgid "Boot parameters are Linux kernel parameters which are generally used to make sure that peripherals are dealt with properly. For the most part, the kernel can auto-detect information about your peripherals. However, in some cases you'll have to help the kernel a bit."
msgstr ""

#: boot-installer.xml:2748
#, no-c-format
#. Tag: para
msgid "If this is the first time you're booting the system, try the default boot parameters (i.e., don't try setting parameters) and see if it works correctly. It probably will. If not, you can reboot later and look for any special parameters that inform the system about your hardware."
msgstr ""

#: boot-installer.xml:2755
#, no-c-format
#. Tag: para
msgid "Information on many boot parameters can be found in the <ulink url=\"http://www.tldp.org/HOWTO/BootPrompt-HOWTO.html\"> Linux BootPrompt HOWTO</ulink>, including tips for obscure hardware. This section contains only a sketch of the most salient parameters. Some common gotchas are included below in <xref linkend=\"boot-troubleshooting\"/>."
msgstr ""

#: boot-installer.xml:2764
#, no-c-format
#. Tag: para
msgid ""
      "When the kernel boots, a message <informalexample><screen>\n"
      "Memory:<replaceable>avail</replaceable>k/<replaceable>total</replaceable>k available\n"
      "</screen></informalexample> should be emitted early in the process. <replaceable>total</replaceable> should match the total amount of RAM, in kilobytes. If this doesn't match the actual amount of RAM you have installed, you need to use the <userinput>mem=<replaceable>ram</replaceable></userinput> parameter, where <replaceable>ram</replaceable> is set to the amount of memory, suffixed with <quote>k</quote> for kilobytes, or <quote>m</quote> for megabytes. For example, both <userinput>mem=65536k</userinput> and <userinput>mem=64m</userinput> mean 64MB of RAM."
msgstr ""

#: boot-installer.xml:2780
#, no-c-format
#. Tag: para
msgid "If you are booting with a serial console, generally the kernel will autodetect this<phrase arch=\"mipsel\"> (although not on DECstations)</phrase>. If you have a videocard (framebuffer) and a keyboard also attached to the computer which you wish to boot via serial console, you may have to pass the <userinput>console=<replaceable>device</replaceable></userinput> argument to the kernel, where <replaceable>device</replaceable> is your serial device, which is usually something like <filename>ttyS0</filename>."
msgstr ""

#: boot-installer.xml:2793
#, no-c-format
#. Tag: para
msgid "For &arch-title; the serial devices are <filename>ttya</filename> or <filename>ttyb</filename>. Alternatively, set the <envar>input-device</envar> and <envar>output-device</envar> OpenPROM variables to <filename>ttya</filename>."
msgstr ""

#: boot-installer.xml:2804
#, no-c-format
#. Tag: title
msgid "Debian Installer Parameters"
msgstr ""

#: boot-installer.xml:2805
#, no-c-format
#. Tag: para
msgid "The installation system recognizes a few additional boot parameters<footnote> <para> Note that the kernel accepts a maximum of 8 command line options and 8 environment options (including any options added by default for the installer). If these numbers are exceeded, 2.4 kernels will drop any excess options and 2.6 kernels will panic. With kernel 2.6.9 or newer, you can use 32 command line options and 32 environment options. </para> </footnote> which may be useful."
msgstr ""

#: boot-installer.xml:2825
#, no-c-format
#. Tag: term
msgid "debconf/priority"
msgstr ""

#: boot-installer.xml:2826
#, no-c-format
#. Tag: para
msgid "This parameter sets the lowest priority of messages to be displayed."
msgstr ""

#: boot-installer.xml:2830
#, no-c-format
#. Tag: para
msgid "The default installation uses <userinput>debconf/priority=high</userinput>. This means that both high and critical priority messages are shown, but medium and low priority messages are skipped. If problems are encountered, the installer adjusts the priority as needed."
msgstr ""

#: boot-installer.xml:2837
#, no-c-format
#. Tag: para
msgid "If you add <userinput>debconf/priority=medium</userinput> as boot parameter, you will be shown the installation menu and gain more control over the installation. When <userinput>debconf/priority=low</userinput> is used, all messages are shown (this is equivalent to the <emphasis>expert</emphasis> boot method). With <userinput>debconf/priority=critical</userinput>, the installation system will display only critical messages and try to do the right thing without fuss."
msgstr ""

#: boot-installer.xml:2851
#, no-c-format
#. Tag: term
msgid "DEBIAN_FRONTEND"
msgstr ""

#: boot-installer.xml:2852
#, no-c-format
#. Tag: para
msgid "This boot parameter controls the type of user interface used for the installer. The current possible parameter settings are: <itemizedlist> <listitem> <para><userinput>DEBIAN_FRONTEND=noninteractive</userinput></para> </listitem><listitem> <para><userinput>DEBIAN_FRONTEND=text</userinput></para> </listitem><listitem> <para><userinput>DEBIAN_FRONTEND=newt</userinput></para> </listitem><listitem> <para><userinput>DEBIAN_FRONTEND=slang</userinput></para> </listitem><listitem> <para><userinput>DEBIAN_FRONTEND=ncurses</userinput></para> </listitem><listitem> <para><userinput>DEBIAN_FRONTEND=bogl</userinput></para> </listitem><listitem> <para><userinput>DEBIAN_FRONTEND=gtk</userinput></para> </listitem><listitem> <para><userinput>DEBIAN_FRONTEND=corba</userinput></para> </listitem> </itemizedlist> The default front end is <userinput>DEBIAN_FRONTEND=newt</userinput>. <userinput>DEBIAN_FRONTEND=text</userinput> may be preferable for serial console installs. Generally only the <userinput>newt</userinput> frontend is available on default install media, so this is not very useful right now."
msgstr ""

#: boot-installer.xml:2888
#, no-c-format
#. Tag: term
msgid "BOOT_DEBUG"
msgstr ""

#: boot-installer.xml:2889
#, no-c-format
#. Tag: para
msgid "Setting this boot parameter to 2 will cause the installer's boot process to be verbosely logged. Setting it to 3 makes debug shells available at strategic points in the boot process. (Exit the shells to continue the boot process.)"
msgstr ""

#: boot-installer.xml:2898
#, no-c-format
#. Tag: userinput
msgid "BOOT_DEBUG=0"
msgstr ""

#: boot-installer.xml:2899
#, no-c-format
#. Tag: para
msgid "This is the default."
msgstr ""

#: boot-installer.xml:2903
#, no-c-format
#. Tag: userinput
msgid "BOOT_DEBUG=1"
msgstr ""

#: boot-installer.xml:2904
#, no-c-format
#. Tag: para
msgid "More verbose than usual."
msgstr ""

#: boot-installer.xml:2908
#, no-c-format
#. Tag: userinput
msgid "BOOT_DEBUG=2"
msgstr ""

#: boot-installer.xml:2909
#, no-c-format
#. Tag: para
msgid "Lots of debugging information."
msgstr ""

#: boot-installer.xml:2913
#, no-c-format
#. Tag: userinput
msgid "BOOT_DEBUG=3"
msgstr ""

#: boot-installer.xml:2914
#, no-c-format
#. Tag: para
msgid "Shells are run at various points in the boot process to allow detailed debugging. Exit the shell to continue the boot."
msgstr ""

#: boot-installer.xml:2928
#, no-c-format
#. Tag: term
msgid "INSTALL_MEDIA_DEV"
msgstr ""

#: boot-installer.xml:2929
#, no-c-format
#. Tag: para
msgid "The value of the parameter is the path to the device to load the Debian installer from. For example, <userinput>INSTALL_MEDIA_DEV=/dev/floppy/0</userinput>"
msgstr ""

#: boot-installer.xml:2935
#, no-c-format
#. Tag: para
msgid "The boot floppy, which normally scans all floppies it can to find the root floppy, can be overridden by this parameter to only look at the one device."
msgstr ""

#: boot-installer.xml:2945
#, no-c-format
#. Tag: term
msgid "debian-installer/framebuffer"
msgstr ""

#: boot-installer.xml:2946
#, no-c-format
#. Tag: para
msgid "Some architectures use the kernel framebuffer to offer installation in a number of languages. If framebuffer causes a problem on your system you can disable the feature by the parameter <userinput>debian-installer/framebuffer=false</userinput>. Problem symptoms are error messages about bterm or bogl, a blank screen, or a freeze within a few minutes after starting the install."
msgstr ""

#: boot-installer.xml:2955
#, no-c-format
#. Tag: para
msgid "The <userinput>video=vga16:off</userinput> argument may also be used to disable the framebuffer. Such problems have been reported on a Dell Inspiron with Mobile Radeon card."
msgstr ""

#: boot-installer.xml:2961
#, no-c-format
#. Tag: para
msgid "Such problems have been reported on the Amiga 1200 and SE/30."
msgstr ""

#: boot-installer.xml:2965
#, no-c-format
#. Tag: para
msgid "Such problems have been reported on hppa."
msgstr ""

#: boot-installer.xml:2969
#, no-c-format
#. Tag: para
msgid "Because of display problems on some systems, framebuffer support is <emphasis>disabled by default</emphasis> for &arch-title;. This can result in ugly display on systems that do properly support the framebuffer, like those with ATI graphical cards. If you see display problems in the installer, you can try booting with parameter <userinput>debian-installer/framebuffer=true</userinput>."
msgstr ""

#: boot-installer.xml:2982
#, no-c-format
#. Tag: term
msgid "debian-installer/probe/usb"
msgstr ""

#: boot-installer.xml:2983
#, no-c-format
#. Tag: para
msgid "Set to <userinput>false</userinput> to prevent probing for USB on boot, if that causes problems."
msgstr ""

#: boot-installer.xml:2992
#, no-c-format
#. Tag: term
msgid "netcfg/disable_dhcp"
msgstr ""

#: boot-installer.xml:2993
#, no-c-format
#. Tag: para
msgid "By default, the &d-i; automatically probes for network configuration via DHCP. If the probe succeeds, you won't have a chance to review and change the obtained settings. You can get to the manual network setup only in case the DHCP probe fails."
msgstr ""

#: boot-installer.xml:3000
#, no-c-format
#. Tag: para
msgid "If you have a DHCP server on your local network, but want to avoid it because e.g. it gives wrong answers, you can use the parameter <userinput>netcfg/disable_dhcp=true</userinput> to prevent configuring the network with DHCP and to enter the information manually."
msgstr ""

#: boot-installer.xml:3011
#, no-c-format
#. Tag: term
msgid "hw-detect/start_pcmcia"
msgstr ""

#: boot-installer.xml:3012
#, no-c-format
#. Tag: para
msgid "Set to <userinput>false</userinput> to prevent starting PCMCIA services, if that causes problems. Some laptops are well known for this misbehavior."
msgstr ""

#: boot-installer.xml:3022
#, no-c-format
#. Tag: term
msgid "preseed/url"
msgstr ""

#: boot-installer.xml:3023
#, no-c-format
#. Tag: para
msgid "Specify the url to a preconfiguration file to download and use in automating the install. See <xref linkend=\"automatic-install\"/>."
msgstr ""

#: boot-installer.xml:3032
#, no-c-format
#. Tag: term
msgid "preseed/file"
msgstr ""

#: boot-installer.xml:3033
#, no-c-format
#. Tag: para
msgid "Specify the path to a preconfiguration file to load to automating the install. See <xref linkend=\"automatic-install\"/>."
msgstr ""

#: boot-installer.xml:3042
#, no-c-format
#. Tag: term
msgid "cdrom-detect/eject"
msgstr ""

#: boot-installer.xml:3043
#, no-c-format
#. Tag: para
msgid "By default, before rebooting, &d-i; automatically ejects the optical media used during the installation. This can be unnecessary if the system does not automatically boot off the CD. In some cases it may even be undesirable, for example if the optical drive cannot reinsert the media itself and the user is not there to do it manually. Many slot loading, slim-line, and caddy style drives cannot reload media automatically."
msgstr ""

#: boot-installer.xml:3052
#, no-c-format
#. Tag: para
msgid "Set to <userinput>false</userinput> to disable automatic ejection, and be aware that you may need to ensure that the system does not automatically boot from the optical drive after the initial installation."
msgstr ""

#: boot-installer.xml:3063
#, no-c-format
#. Tag: term
msgid "ramdisk_size"
msgstr ""

#: boot-installer.xml:3064
#, no-c-format
#. Tag: para
msgid "If you are using a 2.2.x kernel, you may need to set &ramdisksize;."
msgstr ""

#: boot-installer.xml:3072
#, no-c-format
#. Tag: term
msgid "rescue/enable"
msgstr ""

#: boot-installer.xml:3073
#, no-c-format
#. Tag: para
msgid "Set to <userinput>true</userinput> to enter rescue mode rather than performing a normal installation. See <xref linkend=\"rescue\"/>."
msgstr ""

#: boot-installer.xml:3091
#, no-c-format
#. Tag: title
msgid "Troubleshooting the Installation Process"
msgstr ""

#: boot-installer.xml:3096
#, no-c-format
#. Tag: title
msgid "Floppy Disk Reliability"
msgstr ""

#: boot-installer.xml:3098
#, no-c-format
#. Tag: para
msgid "The biggest problem for people using floppy disks to install Debian seems to be floppy disk reliability."
msgstr ""

#: boot-installer.xml:3103
#, no-c-format
#. Tag: para
msgid "The boot floppy is the floppy with the worst problems, because it is read by the hardware directly, before Linux boots. Often, the hardware doesn't read as reliably as the Linux floppy disk driver, and may just stop without printing an error message if it reads incorrect data. There can also be failures in the Driver Floppies most of which indicate themselves with a flood of messages about disk I/O errors."
msgstr ""

#: boot-installer.xml:3112
#, no-c-format
#. Tag: para
msgid "If you are having the installation stall at a particular floppy, the first thing you should do is re-download the floppy disk image and write it to a <emphasis>different</emphasis> floppy. Simply reformatting the old floppy may not be sufficient, even if it appears that the floppy was reformatted and written with no errors. It is sometimes useful to try writing the floppy on a different system."
msgstr ""

#: boot-installer.xml:3122
#, no-c-format
#. Tag: para
msgid "One user reports he had to write the images to floppy <emphasis>three</emphasis> times before one worked, and then everything was fine with the third floppy."
msgstr ""

#: boot-installer.xml:3128
#, no-c-format
#. Tag: para
msgid "Other users have reported that simply rebooting a few times with the same floppy in the floppy drive can lead to a successful boot. This is all due to buggy hardware or firmware floppy drivers."
msgstr ""

#: boot-installer.xml:3137
#, no-c-format
#. Tag: title
msgid "Boot Configuration"
msgstr ""

#: boot-installer.xml:3139
#, no-c-format
#. Tag: para
msgid "If you have problems and the kernel hangs during the boot process, doesn't recognize peripherals you actually have, or drives are not recognized properly, the first thing to check is the boot parameters, as discussed in <xref linkend=\"boot-parms\"/>."
msgstr ""

#: boot-installer.xml:3146
#, no-c-format
#. Tag: para
msgid "If you are booting with your own kernel instead of the one supplied with the installer, be sure that <userinput>CONFIG_DEVFS</userinput> is set in your kernel. The installer requires <userinput>CONFIG_DEVFS</userinput>."
msgstr ""

#: boot-installer.xml:3153
#, no-c-format
#. Tag: para
msgid "Often, problems can be solved by removing add-ons and peripherals, and then trying booting again. <phrase arch=\"i386\">Internal modems, sound cards, and Plug-n-Play devices can be especially problematic.</phrase>"
msgstr ""

#: boot-installer.xml:3159
#, no-c-format
#. Tag: para
msgid "If you have a large amount of memory installed in your machine, more than 512M, and the installer hangs when booting the kernel, you may need to include a boot argument to limit the amount of memory the kernel sees, such as <userinput>mem=512m</userinput>."
msgstr ""

#: boot-installer.xml:3170
#, no-c-format
#. Tag: title
msgid "Common &arch-title; Installation Problems"
msgstr ""

#: boot-installer.xml:3171
#, no-c-format
#. Tag: para
msgid "There are some common installation problems that can be solved or avoided by passing certain boot parameters to the installer."
msgstr ""

#: boot-installer.xml:3176
#, no-c-format
#. Tag: para
msgid "Some systems have floppies with <quote>inverted DCLs</quote>. If you receive errors reading from the floppy, even when you know the floppy is good, try the parameter <userinput>floppy=thinkpad</userinput>."
msgstr ""

#: boot-installer.xml:3182
#, no-c-format
#. Tag: para
msgid "On some systems, such as the IBM PS/1 or ValuePoint (which have ST-506 disk drivers), the IDE drive may not be properly recognized. Again, try it first without the parameters and see if the IDE drive is recognized properly. If not, determine your drive geometry (cylinders, heads, and sectors), and use the parameter <userinput>hd=<replaceable>cylinders</replaceable>,<replaceable>heads</replaceable>,<replaceable>sectors</replaceable></userinput>."
msgstr ""

#: boot-installer.xml:3191
#, no-c-format
#. Tag: para
msgid "If you have a very old machine, and the kernel hangs after saying <computeroutput>Checking 'hlt' instruction...</computeroutput>, then you should try the <userinput>no-hlt</userinput> boot argument, which disables this test."
msgstr ""

#: boot-installer.xml:3198
#, no-c-format
#. Tag: para
msgid "If your screen begins to show a weird picture while the kernel boots, eg. pure white, pure black or colored pixel garbage, your system may contain a problematic video card which does not switch to the framebuffer mode properly. Then you can use the boot parameter <userinput>debian-installer/framebuffer=false</userinput> or <userinput>video=vga16:off</userinput> to disable the framebuffer console. Only the English language will be available during the installation due to limited console features. See <xref linkend=\"boot-parms\"/> for details."
msgstr ""

#: boot-installer.xml:3213
#, no-c-format
#. Tag: title
msgid "System Freeze During the PCMCIA Configuration Phase"
msgstr ""

#: boot-installer.xml:3214
#, no-c-format
#. Tag: para
msgid "Some laptop models produced by Dell are known to crash when PCMCIA device detection tries to access some hardware addresses. Other laptops may display similar problems. If you experience such a problem and you don't need PCMCIA support during the installation, you can disable PCMCIA using the <userinput>hw-detect/start_pcmcia=false</userinput> boot parameter. You can then configure PCMCIA after the installation is completed and exclude the resource range causing the problems."
msgstr ""

#: boot-installer.xml:3224
#, no-c-format
#. Tag: para
msgid "Alternatively, you can boot the installer in expert mode. You will then be asked to enter the resource range options your hardware needs. For example, if you have one of the Dell laptops mentioned above, you should enter <userinput>exclude port 0x800-0x8ff</userinput> here. There is also a list of some common resource range options in the <ulink url=\"http://pcmcia-cs.sourceforge.net/ftp/doc/PCMCIA-HOWTO-1.html#ss1.12\">System resource settings section of the PCMCIA HOWTO</ulink>. Note that you have to omit the commas, if any, when you enter this value in the installer."
msgstr ""

#: boot-installer.xml:3241
#, no-c-format
#. Tag: title
msgid "System Freeze while Loading the USB Modules"
msgstr ""

#: boot-installer.xml:3242
#, no-c-format
#. Tag: para
msgid "The kernel normally tries to install USB modules and the USB keyboard driver in order to support some non-standard USB keyboards. However, there are some broken USB systems where the driver hangs on loading. A possible workaround may be disabling the USB controller in your mainboard BIOS setup. Another option is passing the <userinput>debian-installer/probe/usb=false</userinput> parameter at the boot prompt, which will prevent the modules from being loaded."
msgstr ""

#: boot-installer.xml:3256
#, no-c-format
#. Tag: title
msgid "Interpreting the Kernel Startup Messages"
msgstr ""

#: boot-installer.xml:3258
#, no-c-format
#. Tag: para
msgid "During the boot sequence, you may see many messages in the form <computeroutput>can't find <replaceable>something</replaceable> </computeroutput>, or <computeroutput> <replaceable>something</replaceable> not present</computeroutput>, <computeroutput>can't initialize <replaceable>something</replaceable> </computeroutput>, or even <computeroutput>this driver release depends on <replaceable>something</replaceable> </computeroutput>. Most of these messages are harmless. You see them because the kernel for the installation system is built to run on computers with many different peripheral devices. Obviously, no one computer will have every possible peripheral device, so the operating system may emit a few complaints while it looks for peripherals you don't own. You may also see the system pause for a while. This happens when it is waiting for a device to respond, and that device is not present on your system. If you find the time it takes to boot the system unacceptably long, you can create a custom kernel later (see <xref linkend=\"kernel-baking\"/>)."
msgstr ""

#: boot-installer.xml:3283
#, no-c-format
#. Tag: title
msgid "Bug Reporter"
msgstr ""

#: boot-installer.xml:3284
#, no-c-format
#. Tag: para
msgid "If you get through the initial boot phase but cannot complete the install, the bug reporter menu choice may be helpful. It lets you store system error logs and configuration information from the installer to a floppy, or download them in a web browser. This information may provide clues as to what went wrong and how to fix it. If you are submitting a bug report you may want to attach this information to the bug report."
msgstr ""

#: boot-installer.xml:3295
#, no-c-format
#. Tag: para
msgid "Other pertinent installation messages may be found in <filename>/var/log/</filename> during the installation, and <filename>/var/log/installer/</filename> after the computer has been booted into the installed system."
msgstr ""

#: boot-installer.xml:3306
#, no-c-format
#. Tag: title
msgid "Submitting Installation Reports"
msgstr ""

#: boot-installer.xml:3307
#, no-c-format
#. Tag: para
msgid "If you still have problems, please submit an installation report. We also encourage installation reports to be sent even if the installation is successful, so that we can get as much information as possible on the largest number of hardware configurations."
msgstr ""

#: boot-installer.xml:3314
#, no-c-format
#. Tag: para
msgid "If you have a working Debian system, the easiest way to send an installation report is to install the installation-report and reportbug packages (<command>apt-get install installation-report reportbug</command>) and run the command <command>reportbug installation-report</command>."
msgstr ""

#: boot-installer.xml:3321
#, no-c-format
#. Tag: para
msgid ""
      "Please use this template when filling out installation reports, and file the report as a bug report against the <classname>installation-reports</classname> pseudo package, by sending it to <email>submit@bugs.debian.org</email>. <informalexample><screen>\n"
      "Package: installation-reports\n"
      "\n"
      "Boot method: &lt;How did you boot the installer? CD? floppy? network?&gt;\n"
      "Image version: &lt;Fill in date and from where you got the image&gt;\n"
      "Date: &lt;Date and time of the install&gt;\n"
      "\n"
      "Machine: &lt;Description of machine (eg, IBM Thinkpad R32)&gt;\n"
      "Processor:\n"
      "Memory:\n"
      "Partitions: &lt;df -Tl will do; the raw partition table is preferred&gt;\n"
      "\n"
      "Output of lspci and lspci -n:\n"
      "\n"
      "Base System Installation Checklist:\n"
      "[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it\n"
      "\n"
      "Initial boot worked:    [ ]\n"
      "Configure network HW:   [ ]\n"
      "Config network:         [ ]\n"
      "Detect CD:              [ ]\n"
      "Load installer modules: [ ]\n"
      "Detect hard drives:     [ ]\n"
      "Partition hard drives:  [ ]\n"
      "Create file systems:    [ ]\n"
      "Mount partitions:       [ ]\n"
      "Install base system:    [ ]\n"
      "Install boot loader:    [ ]\n"
      "Reboot:                 [ ]\n"
      "\n"
      "Comments/Problems:\n"
      "\n"
      "&lt;Description of the install, in prose, and any thoughts, comments\n"
      "      and ideas you had during the initial install.&gt;\n"
      "</screen></informalexample> In the bug report, describe what the problem is, including the last visible kernel messages in the event of a kernel hang. Describe the steps that you did which brought the system into the problem state."
msgstr ""