Now it is time to partition your disks. If you are uncomfortable with partitioning, or just want to know more details, see . First you will be given the opportunity to automatically partition either an entire drive, or free space on a drive. This is also called guided partitioning. If you do not want to autopartition, choose Manually edit partition table from the menu. If you choose guided partitioning, you may have two options: to create partitions directly on the hard disk (classic method) or to use Logical Volume Management (LVM). In the second case, the installer will create most partitions inside one big partition; the advantage of this method is that partitions inside this big partition can be resized relatively easily later. Note: the option to use LVM may not be available on all architectures. After you choose guided partitioning (either classic or using LVM), you will be able to choose from the schemes listed in the table below. All schemes have their pros and cons, some of which are discussed in . If you are unsure, choose the first one. Bear in mind that guided partitioning needs a certain minimal amount of free space to operate with. If you don't give it at least about 1GB of space (depends on chosen scheme), guided partitioning will fail. Partitioning scheme Minimum space Created partitions All files in one partition 600MB /, swap Separate /home partition 500MB /, /home, swap Separate /home, /usr, /var and /tmp partitions 1GB /, /home, /usr, /var, /tmp, swap If you choose guided partitioning using LVM, the installer will also create a separate /boot partition. The other partitions, except for the swap partition, will be created inside the LVM partition. If you choose guided partitioning for your IA64 system, there will be an additional partition, formatted as a FAT16 bootable filesystem, for the EFI boot loader. There is also an additional menu item in the formatting menu to manually set up a partition as an EFI boot partition. If you choose guided partitioning for your Alpha system, an additional, unformatted partition will be allocated at the beginning of your disk to reserve this space for the aboot boot loader. After selecting a scheme, the next screen will show your new partition table, including information on whether and how partitions will be formatted and where they will be mounted. The list of partitions might look like this: IDE1 master (hda) - 6.4 GB WDC AC36400L #1 primary 16.4 MB B f ext2 /boot #2 primary 551.0 MB swap swap #3 primary 5.8 GB ntfs pri/log 8.2 MB FREE SPACE IDE1 slave (hdb) - 80.0 GB ST380021A #1 primary 15.9 MB ext3 #2 primary 996.0 MB fat16 #3 primary 3.9 GB xfs /home #5 logical 6.0 GB f ext3 / #6 logical 1.0 GB f ext3 /var #7 logical 498.8 MB ext3 #8 logical 551.5 MB swap swap #9 logical 65.8 GB ext2 This example shows two IDE harddrives divided into several partitions; the first disk has some free space. Each partition line consists of the partition number, its type, size, optional flags, file system, and mountpoint (if any). Note: this particular setup cannot be created using guided partitioning but it does show possible variation that can be achieved using manual partitioning). This concludes the guided partitioning. If you are satisfied with the generated partition table, you can choose Finish partitioning and write changes to disk from the menu to implement the new partition table (as described at the end of this section). If you are not happy, you can choose to Undo changes to partitions If you selected guided partitioning using LVM, you will not be able to undo all changes made as some changes will already have been committed to the hard disk. The installer will warn you before that happens though. and run guided partitioning again, or modify the proposed changes as described below for manual partitioning. A similar screen to the one shown just above will be displayed if you choose manual partitioning except that your existing partition table will be shown and without the mount points. How to manually setup your partition table and the usage of partitions by your new Debian system will be covered in the remainder of this section. If you select a pristine disk which doesn't have neither partitions nor free space on it, you will be offered to create a new partition table (this is needed so you can create new partitions). After this a new line entitled FREE SPACE should appear under the selected disk. If you select some free space, you will be offered to create new partition. You will have to answer a quick series of questions about its size, type (primary or logical), and location (beginning or end of the free space). After this, you will be presented with detailed overview of your new partition. There are options like mountpoint, mount options, bootable flag, or way of usage. If you don't like the preselected defaults, feel free to change them to your liking. E.g. by selecting the option Use as:, you can choose different filesystem for this partition including the possibility to use the partition for swap, software RAID, LVM, or not use it at all. Other nice feature is the possibility to copy data from existing partition onto this one. When you are satisfied with your new partition, select Done setting up the partition and you will be thrown back to partman's main screen. If you decide you want to change something about your partition, simply select the partition, which will bring you to the partition configuration menu. Because this is the same screen like when creating a new partition, you can change the same set of options. One thing which might not be very obvious at a first glance is that you can resize the partition by selecting the item displaying the size of the partition. Filesystems known to work are at least fat16, fat32, ext2, ext3 and swap. This menu also allows you to delete a partition. Be sure to create at least two partitions: one for the root filesystem (which must be mounted as /) and one for swap. If you forget to mount the root filesystem, partman won't let you continue until you correct this issue. If you forget to select and format an EFI boot partition, partman will detect this and will not let you continue until you allocate one. Capabilities of partman can be extended with installer modules, but are dependent on your system's architecture. So if you can't see all promised goodies, check if you have loaded all required modules (e.g. partman-ext3, partman-xfs, or partman-lvm). After you are satisfied with partitioning, select Finish partitioning and write changes to disk from the partitioning menu. You will be presented with a summary of changes made to the disks and asked to confirm that the filesystems should be created as requested.