From 7b25bd0caf707ef6dfa239e2d69d0e2817b3a1a9 Mon Sep 17 00:00:00 2001
From: Frans Pop <elendil@planet.nl>
Date: Wed, 16 Aug 2006 20:36:24 +0000
Subject: - Update info on setting up RARP; thanks Nathanael Nerode - Remove
 info for servers running 2.2 kernels, these should no longer be allowed to
 exist

---
 en/install-methods/tftp/rarp.xml | 51 ++++++++--------------------------------
 1 file changed, 10 insertions(+), 41 deletions(-)

(limited to 'en')

diff --git a/en/install-methods/tftp/rarp.xml b/en/install-methods/tftp/rarp.xml
index e59b94587..89ad3fb7e 100644
--- a/en/install-methods/tftp/rarp.xml
+++ b/en/install-methods/tftp/rarp.xml
@@ -3,10 +3,10 @@
 
 
   <sect2 condition="supports-rarp" id="tftp-rarp">
-   <title>Setting up RARP server</title>
+  <title>Setting up RARP server</title>
 <para>
 
-To setup RARP, you need to know the Ethernet address (a.k.a. the MAC address)
+To set up RARP, you need to know the Ethernet address (a.k.a. the MAC address)
 of the client computers to be installed.
 If you don't know this information, you can
 
@@ -18,47 +18,16 @@ command <userinput>/sbin/ifconfig eth0</userinput>.
 
 </para><para>
 
-On a RARP server system using a Linux 2.2.x kernel,
-you need to populate the kernel's RARP table.
-To do this, run the following commands:
-
-<informalexample><screen>
-# <userinput>/sbin/rarp -s
-<replaceable>client-hostname</replaceable>
-<replaceable>client-enet-addr</replaceable></userinput>
-
-# <userinput>/usr/sbin/arp -s
-<replaceable>client-ip</replaceable>
-<replaceable>client-enet-addr</replaceable></userinput>
-</screen></informalexample>
-
-If you get
-
-<informalexample><screen>
-SIOCSRARP: Invalid argument
-</screen></informalexample>
-
-you probably need to load the RARP kernel module or else recompile the
-kernel to support RARP.  Try <userinput>modprobe rarp</userinput> and
-then try the <command>rarp</command> command again.
-
-</para><para>
-
-On a RARP server system using a Linux 2.4.x kernel,
-there is no RARP module, and
-you should instead use the <command>rarpd</command> program.  The
-procedure is similar to that used under SunOS in the following
-paragraph.
-
-</para><para>
-
-Under SunOS, you need to ensure that the Ethernet hardware address for
-the client is listed in the <quote>ethers</quote> database (either in the
+On a RARP server system using a Linux 2.4 or 2.6 kernel, or Solaris/SunOS,
+you use the <command>rarpd</command> program.
+You need to ensure that the Ethernet hardware address for the client is
+listed in the <quote>ethers</quote> database (either in the
 <filename>/etc/ethers</filename> file, or via NIS/NIS+) and in the
 <quote>hosts</quote> database. Then you need to start the RARP daemon.
-In SunOS 4, issue the command (as root):
-<userinput>/usr/etc/rarpd -a</userinput>; in SunOS 5, use
-<userinput>/usr/sbin/rarpd -a</userinput>.
+Issue the command (as root): <userinput>/usr/sbin/rarpd -a</userinput>
+on most Linux systems and SunOS 5 (Solaris 2),
+<userinput>/usr/sbin/in.rarpd -a</userinput> on some other Linux systems,
+or <userinput>/usr/etc/rarpd -a</userinput> in SunOS 4 (Solaris 1).
 
 </para>
   </sect2>
-- 
cgit v1.2.3