From 5abaf8b8372e1937b1056785c6c38d41aa4347bc Mon Sep 17 00:00:00 2001
From: Samuel Thibault <sthibault@debian.org>
Date: Thu, 16 Sep 2010 22:09:05 +0000
Subject: Drop a few section from non-Linux archs.

---
 en/boot-installer/parameters.xml | 8 ++++----
 en/boot-installer/trouble.xml    | 4 ++--
 2 files changed, 6 insertions(+), 6 deletions(-)

(limited to 'en')

diff --git a/en/boot-installer/parameters.xml b/en/boot-installer/parameters.xml
index 4cc17c8f9..909090c54 100644
--- a/en/boot-installer/parameters.xml
+++ b/en/boot-installer/parameters.xml
@@ -2,7 +2,7 @@
 <!-- $Id$ -->
 
  <sect1 id="boot-parms"><title>Boot Parameters</title>
-<para>
+<para arch="linux-any">
 
 Boot parameters are Linux kernel parameters which are generally used
 to make sure that peripherals are dealt with properly.  For the most
@@ -16,7 +16,7 @@ boot parameters (i.e., don't try setting parameters) and see if it works
 correctly. It probably will.  If not, you can reboot later and look for
 any special parameters that inform the system about your hardware.
 
-</para><para>
+</para><para arch="linux-any">
 
 Information on many boot parameters can be found in the
 <ulink url="http://www.tldp.org/HOWTO/BootPrompt-HOWTO.html"> Linux
@@ -25,7 +25,7 @@ section contains only a sketch of the most salient parameters.  Some
 common gotchas are included below in
 <xref linkend="boot-troubleshooting"/>.
 
-</para><para>
+</para><para arch="linux-any">
 
 When the kernel boots, a message
 
@@ -43,7 +43,7 @@ suffixed with <quote>k</quote> for kilobytes, or <quote>m</quote> for
 megabytes.  For example, both <userinput>mem=65536k</userinput> and
 <userinput>mem=64m</userinput> mean 64MB of RAM.
 
-</para><para condition="supports-serial-console">
+</para><para arch="linux-any" condition="supports-serial-console">
 
 If you are booting with a serial console, generally the kernel will
 autodetect this.
diff --git a/en/boot-installer/trouble.xml b/en/boot-installer/trouble.xml
index 6325c4a5f..a07914193 100644
--- a/en/boot-installer/trouble.xml
+++ b/en/boot-installer/trouble.xml
@@ -68,7 +68,7 @@ at high speeds using a modern CD writer.
   <listitem><para>
 
 If your system boots correctly from the CD-ROM, it does not necessarily
-mean that Linux also supports the CD-ROM (or, more correctly, the controller
+mean that &arch-kernel; also supports the CD-ROM (or, more correctly, the controller
 that your CD-ROM drive is connected to). 
 
   </para></listitem>
@@ -131,7 +131,7 @@ detected, sometimes simply trying again may solve the problem. If you have
 more than one CD-ROM drive, try changing the CD-ROM to the other drive.
 If that does not work or if the CD-ROM is recognized but there are errors
 when reading from it, try the suggestions listed below. Some basic knowledge
-of Linux is required for this.
+of &arch-kernel; is required for this.
 To execute any of the commands, you should first switch to the second
 virtual console (VT2) and activate the shell there.
 
-- 
cgit v1.2.3