From ac3fdda5a27e2c2ba6e1cf705a2f05ab4e186f4c Mon Sep 17 00:00:00 2001 From: Frans Pop Date: Mon, 2 Nov 2009 22:52:49 +0000 Subject: Remove m68k from English version of the manual --- en/bookinfo.xml | 19 -- en/boot-installer/accessibility.xml | 2 +- en/boot-installer/boot-installer.xml | 3 +- en/boot-installer/m68k.xml | 363 ---------------------------- en/boot-installer/parameters.xml | 6 +- en/boot-new/boot-new.xml | 76 ------ en/hardware/buying-hardware.xml | 16 -- en/hardware/hardware-supported.xml | 21 -- en/hardware/installation-media.xml | 15 -- en/hardware/memory-disk-requirements.xml | 29 --- en/hardware/network-cards.xml | 3 - en/hardware/supported/m68k.xml | 39 --- en/install-methods/create-floppy.xml | 6 - en/install-methods/download/m68k.xml | 23 -- en/install-methods/downloading-files.xml | 1 - en/install-methods/floppy/m68k.xml | 27 --- en/install-methods/install-tftp.xml | 21 -- en/partitioning/device-names.xml | 20 -- en/partitioning/schemes.xml | 5 - en/post-install/shutdown.xml | 2 +- en/preparing/backup.xml | 11 - en/preparing/bios-setup/m68k.xml | 23 -- en/preparing/minimum-hardware-reqts.xml | 5 - en/preparing/needed-info.xml | 14 +- en/preparing/non-debian-partitioning.xml | 6 - en/preparing/nondeb-part/m68k.xml | 127 ---------- en/preparing/pre-install-bios-setup.xml | 17 +- en/using-d-i/modules/clock-setup-finish.xml | 2 +- en/using-d-i/modules/nobootloader.xml | 4 +- 29 files changed, 9 insertions(+), 897 deletions(-) delete mode 100644 en/boot-installer/m68k.xml delete mode 100644 en/hardware/supported/m68k.xml delete mode 100644 en/install-methods/download/m68k.xml delete mode 100644 en/install-methods/floppy/m68k.xml delete mode 100644 en/preparing/bios-setup/m68k.xml delete mode 100644 en/preparing/nondeb-part/m68k.xml diff --git a/en/bookinfo.xml b/en/bookinfo.xml index 7e6fdb3fa..b8b5d87d1 100644 --- a/en/bookinfo.xml +++ b/en/bookinfo.xml @@ -14,25 +14,6 @@ information on how to make the most of your new Debian system. - -Because the &arch-title; port is not a release architecture for -&releasename;, there is no official version of this manual for -&arch-title; for &releasename;. However, because the port is still -active and there is hope that &arch-title; may be included again -in future official releases, this development version of the -Installation Guide is still available. - - - -Because &arch-title; is not an official architecture, some of the -information, and especially some links, in this manual may be -incorrect. For additional information, please check the -webpages of the port or contact the -debian-&arch-listname; mailing -list. - - - This installation guide is based on an earlier manual written for the old Debian installation system (the boot-floppies), and has diff --git a/en/boot-installer/accessibility.xml b/en/boot-installer/accessibility.xml index 73aef393b..a042e7c10 100644 --- a/en/boot-installer/accessibility.xml +++ b/en/boot-installer/accessibility.xml @@ -9,7 +9,7 @@ Some users may need specific support because of e.g. some visual impairment. USB braille displays are detected automatically, but most other -Most +Most accessibility features have to be enabled manually. On machines that support it, the boot menu emits a beep when it is ready to receive keystrokes. diff --git a/en/boot-installer/boot-installer.xml b/en/boot-installer/boot-installer.xml index 8dc497914..057d730f9 100644 --- a/en/boot-installer/boot-installer.xml +++ b/en/boot-installer/boot-installer.xml @@ -5,7 +5,7 @@ - + Booting the Installer on &arch-title; @@ -35,7 +35,6 @@ For information on how to boot the graphical installer, see &boot-installer-x86.xml; &boot-installer-ia64.xml; -&boot-installer-m68k.xml; &boot-installer-mips.xml; &boot-installer-mipsel.xml; &boot-installer-s390.xml; diff --git a/en/boot-installer/m68k.xml b/en/boot-installer/m68k.xml deleted file mode 100644 index 4346cf868..000000000 --- a/en/boot-installer/m68k.xml +++ /dev/null @@ -1,363 +0,0 @@ - - - - Choosing an Installation Method - - - -Some &arch-title; subarchs have the option of booting using either a -2.4.x or 2.2.x linux kernel. When such a choice exists, try the 2.4.x -linux kernel. The installer should also require less memory when using -a 2.4.x linux kernel as 2.2.x support requires a fixed-sized ramdisk -and 2.4.x uses tmpfs. - - - -If you are using a 2.2.x linux kernel, then you need to use the &ramdisksize; -kernel parameter. - - - -Make sure root=/dev/ram is one of your kernel -parameters. - - - -If you're having trouble, check -cts's &arch-title; debian-installer FAQ. - - - - - - - - - - - - - - Amiga - - -The only method of installation available to amiga is the hard drive -(see ). -In other words the cdrom is not bootable. - - - -Amiga does not currently work with bogl, so if -you are seeing bogl errors, you need to include the boot parameter -fb=false. - - - - - Atari - - -The installer for atari may be started from either the hard -drive (see ) or from floppies -(see ). -In other words the cdrom is not bootable. - - - -Atari does not currently work with bogl, so if -you are seeing bogl errors, you need to include the boot parameter -fb=false. - - - - - BVME6000 - - -The installer for BVME6000 may be started from a cdrom -(see ), floppies -(see ), or the net -(see ). - - - - - Macintosh - - -The only method of installation available to mac is from -the hard drive (see ). -In other words the cdrom is not bootable. -Macs do not have a working 2.4.x kernel. - - - -If your hardware uses a 53c9x-based scsi bus, then you may need to -include the kernel parameter mac53c9x=1,0. -Hardware with two such scsi buses, such as the Quadra 950, will need -mac53c9x=2,0 instead. Alternatively, the -parameter can be specified as mac53c9x=-1,0 -which will leave autodetection on, but which will disable SCSI -disconnects. Note that specifying this parameter is only necessary -if you have more than one hard disk; otherwise, the system will run -faster if you do not specify it. - - - - - MVME147 and MVME16x - - -The installer for MVME147 and MVME16x may be started from -either floppies (see ) -or the net (see ). -In other words the cdrom is not bootable. - - - - - Q40/Q60 - - -The only method of installation available to Q40/Q60 is -from the hard drive (see ). -In other words the cdrom is not bootable. - - - - - - - Booting from a Hard Disk - -&boot-installer-intro-hd.xml; - - - -At least six different ramdisks may be used to boot from the hard -drive, three different types each with and without support for a -2.2.x linux kernel (see -MANIFEST -for details). - - - -The three different types of ramdisks are cdrom, -hd-media, and nativehd. These -ramdisks differ only in their source for installation packages. -The cdrom ramdisk uses a cdrom to get -debian-installer packages. The hd-media ramdisk -uses an iso image file of a cdrom currently residing on a hard disk. -Finally, the nativehd ramdisk uses the net to -install packages. - - - - - - - - - - - - Booting from AmigaOS - - -In the Workbench, start the Linux installation -process by double-clicking on the StartInstall icon -in the debian directory. - - - -You may have to press the &enterkey; key twice after the Amiga -installer program has output some debugging information into a window. -After this, the screen will go grey, there will be a few seconds' -delay. Next, a black screen with white text should come up, displaying -all kinds of kernel debugging information. These messages may scroll -by too fast for you to read, but that's OK. After a couple of -seconds, the installation program should start automatically, so you -can continue down at . - - - - - - Booting from Atari TOS - - -At the GEM desktop, start the Linux installation process by -double-clicking on the bootstra.prg icon in the -debian directory and clicking -Ok at the program options dialog box. - - - -You may have to press the &enterkey; key after the Atari -bootstrap program has output some debugging information into a -window. After this, the screen will go grey, there will be a few -seconds' delay. Next, a black screen with white text should come up, -displaying all kinds of kernel debugging information. These messages -may scroll by too fast for you to read, but that's OK. After a couple -of seconds, the installation program should start automatically, so -you can continue below at . - - - - - - Booting from MacOS - - -You must retain the original Mac system and -boot from it. It is essential that, when booting -MacOS in preparation for booting the Penguin linux loader, you -hold the shift key down to prevent extensions from -loading. If you don't use MacOS except for loading linux, you can -accomplish the same thing by removing all extensions and control -panels from the Mac's System Folder. Otherwise extensions may be left -running and cause random problems with the running linux kernel. - - - -Macs require the Penguin bootloader, which can be -downloaded from the Linux/mac68k -sourceforge.net project. If you do not have the tools to handle -a Stuffit archive, you can put it on a -MacOS-formatted floppy using a second GNU/Linux machine of any -architecture and the hmount, -hcopy, and humount tools from the -hfsutils suite. - - - -At the MacOS desktop, start the Linux installation process by -double-clicking on the Penguin Prefs icon in -the Penguin directory. The -Penguin booter will start up. Go to the -Settings item in the -File menu, click the -Kernel tab. Select the kernel -(vmlinuz) and ramdisk -(initrd.gz) images in the -install directory by clicking on the corresponding -buttons in the upper right corner, and navigating the file select -dialogs to locate the files. - - - -To set the boot parameters in Penguin, choose File -> -Settings..., then switch to the -Options tab. Boot parameters may be typed in to -the text entry area. If you will always want to use these settings, -select File -> Save Settings as -Default. - - - -Close the Settings -dialog, save the settings and start the bootstrap using the -Boot Now item in the -File menu. - - - -The Penguin booter will output some debugging -information into a window. After this, the screen will go grey, there -will be a few seconds' delay. Next, a black screen with white text -should come up, displaying all kinds of kernel debugging -information. These messages may scroll by too fast for you to read, -but that's OK. After a couple of seconds, the installation program -should start automatically, so you can continue below at -. - - - - - - Booting from Q40/Q60 - - - -FIXME - - - -The installation program should start automatically, so you can -continue below at . - - - - - - - - Booting from a CD-ROM - - -Currently, the only &arch-title; subarchitecture that -supports CD-ROM booting is the BVME6000. - - - -&boot-installer-intro-cd.xml; - - - - - Booting with TFTP - -&boot-installer-intro-net.xml; - - - -After booting the VMEbus systems you will be presented with the LILO -Boot: prompt. At that prompt enter one of the -following to boot Linux and begin installation proper of the Debian -software using vt102 terminal emulation: - - - - - - - -type i6000 &enterkey; to install a BVME4000/6000 - - - - -type i162 &enterkey; to install an MVME162 - - - - -type i167 &enterkey; to install an MVME166/167 - - - - - - -You may additionally append the string -TERM=vt100 to use vt100 terminal emulation, -e.g., i6000 TERM=vt100 &enterkey;. - - - - - - - Booting from Floppies - - -For most &arch-title; architectures, booting from a local filesystem is the -recommended method. - - - -Booting from the boot floppy is supported only for Atari and VME -(with a SCSI floppy drive on VME) at this time. - - - diff --git a/en/boot-installer/parameters.xml b/en/boot-installer/parameters.xml index 8eae5a8cb..0c091141a 100644 --- a/en/boot-installer/parameters.xml +++ b/en/boot-installer/parameters.xml @@ -254,10 +254,6 @@ The video=vga16:off argument may also be used to disable the kernel's use of the framebuffer. Such problems have been reported on a Dell Inspiron with Mobile Radeon card. - - -Such problems have been reported on the Amiga 1200 and SE/30. - Such problems have been reported on hppa. @@ -420,7 +416,7 @@ disable that authentication. - + ramdisk_size diff --git a/en/boot-new/boot-new.xml b/en/boot-new/boot-new.xml index 6541061bd..8b295b00b 100644 --- a/en/boot-new/boot-new.xml +++ b/en/boot-new/boot-new.xml @@ -52,82 +52,6 @@ or not detected correctly, please file an installation report. - BVME 6000 Booting - - -If you have just performed a diskless install on a BVM or Motorola -VMEbus machine: once the system has loaded the -tftplilo program from the TFTP server, from the -LILO Boot: prompt enter one of: - - - - -b6000 followed by &enterkey; -to boot a BVME 4000/6000 - - - -b162 followed by &enterkey; -to boot an MVME162 - - - -b167 followed by &enterkey; -to boot an MVME166/167 - - - - - - - - - Macintosh Booting - - - -Go to the directory containing the installation files and start up the -Penguin booter, holding down the -command key. Go to the -Settings dialogue ( -command T ), and locate -the kernel options line which should look like -root=/dev/ram ramdisk_size=15000 or similar. - - - -You need to change the entry to -root=/dev/yyyy. -Replace the yyyy with the Linux name of the -partition onto which you installed the system (e.g. -/dev/sda1); you wrote this down earlier. For users -with tiny screens, adding fbcon=font:VGA8x8 (or -video=font:VGA8x8 on pre-2.6 kernels) may help -readability. You can change this at any time. - - - -If you don't want to start GNU/Linux immediately each time you start, -uncheck the Auto Boot option. Save your -settings in the Prefs file using the -Save Settings As Default option. - - - -Now select Boot Now ( -command B ) to start your -freshly installed GNU/Linux instead of the RAMdisk installer system. - - - -Debian should boot, and you should see the same messages as -when you first booted the installation system, followed by some new -messages. - - - - OldWorld PowerMacs diff --git a/en/hardware/buying-hardware.xml b/en/hardware/buying-hardware.xml index 60eb7c7d4..9fb757631 100644 --- a/en/hardware/buying-hardware.xml +++ b/en/hardware/buying-hardware.xml @@ -11,11 +11,6 @@ distributions of GNU/Linux for the privilege, but it does buy a level of peace of mind, since you can be sure that the hardware is well-supported by GNU/Linux. - - -Unfortunately, it's quite rare to find any vendor shipping -new &arch-title; machines at all. - If you do have to buy a machine with Windows bundled, carefully read @@ -43,17 +38,6 @@ for their hardware. Others won't allow us access to the documentation without a non-disclosure agreement that would prevent us from releasing the Linux source code. - - -Another example is the proprietary hardware in the older -Macintosh line. In fact, no specifications or documentation have ever -been released for any Macintosh hardware, most notably the ADB -controller (used by the mouse and keyboard), the floppy controller, -and all acceleration and CLUT manipulation of the video hardware -(though we do now support CLUT manipulation on nearly all internal -video chips). In a nutshell, this explains why the Macintosh Linux -port lags behind other Linux ports. - Since we haven't been granted access to the documentation on these diff --git a/en/hardware/hardware-supported.xml b/en/hardware/hardware-supported.xml index 2f96fa518..f25468c63 100644 --- a/en/hardware/hardware-supported.xml +++ b/en/hardware/hardware-supported.xml @@ -127,26 +127,6 @@ variations of each architecture known as flavors. 5kc-malta - - Motorola 680x0 - m68k - Atari - atari - - Amiga - amiga - - 68k Macintosh - mac - - VME - bvme6000 - - mvme147 - - mvme16x - - IBM/Motorola PowerPC powerpc @@ -220,7 +200,6 @@ as well. &supported-hppa.xml; &supported-i386.xml; &supported-ia64.xml; -&supported-m68k.xml; &supported-mips.xml; &supported-mipsel.xml; &supported-powerpc.xml; diff --git a/en/hardware/installation-media.xml b/en/hardware/installation-media.xml index 8c6e6def3..541b506cb 100644 --- a/en/hardware/installation-media.xml +++ b/en/hardware/installation-media.xml @@ -96,11 +96,6 @@ Booting the installation system directly from a hard disk is another option for many architectures. This will require some other operating system to load the installer onto the hard disk. - - -In fact, installation from your local disk is the preferred -installation technique for most &architecture; machines. - Although the &arch-title; does not allow booting from SunOS @@ -190,16 +185,6 @@ SCSI disk controllers from many different manufacturers are supported. See the Linux Hardware Compatibility HOWTO for more details. - - -Pretty much all storage systems supported by the Linux kernel are -supported by the Debian installation system. Note that the current -Linux kernel does not support floppies on the Macintosh at all, and -the Debian installation system doesn't support floppies for Amigas. -Also supported on the Atari is the Macintosh HFS system, and AFFS as a -module. Macs support the Atari (FAT) file system. Amigas support the -FAT file system, and HFS as a module. - Any storage system supported by the Linux kernel is also supported by diff --git a/en/hardware/memory-disk-requirements.xml b/en/hardware/memory-disk-requirements.xml index 7adc6961e..a6566cb37 100644 --- a/en/hardware/memory-disk-requirements.xml +++ b/en/hardware/memory-disk-requirements.xml @@ -28,35 +28,6 @@ the former should be selected. or disk space available may be possible but is only advised for experienced users. - - -On the Amiga the size of FastRAM is relevant towards the total memory -requirements. Also, using Zorro cards with 16-bit RAM is not -supported; you'll need 32-bit RAM. The amiboot -program can be used to disable 16-bit RAM; see the -Linux/m68k FAQ. Recent kernels should -disable 16-bit RAM automatically. - - - -On the Atari, both ST-RAM and Fast RAM (TT-RAM) are used by Linux. -Many users have reported problems running the kernel itself in Fast -RAM, so the Atari bootstrap will place the kernel in ST-RAM. The -minimum requirement for ST-RAM is 2 MB. You will need an additional -12 MB or more of TT-RAM. - - - -On the Macintosh, care should be taken on machines with RAM-based -video (RBV). The RAM segment at physical address 0 is used as screen -memory, making the default load position for the kernel unavailable. -The alternate RAM segment used for kernel and RAMdisk must be at least -4 MB. - - - -FIXME: is this still true? - diff --git a/en/hardware/network-cards.xml b/en/hardware/network-cards.xml index e3efafdf1..be142f984 100644 --- a/en/hardware/network-cards.xml +++ b/en/hardware/network-cards.xml @@ -12,9 +12,6 @@ should normally be loaded automatically. This includes most PCI and PCMCIA cards. Many older ISA cards are supported as well. -Again, see -for complete details. - This includes a lot of generic PCI cards (for systems that have PCI) and diff --git a/en/hardware/supported/m68k.xml b/en/hardware/supported/m68k.xml deleted file mode 100644 index 6f33d20e3..000000000 --- a/en/hardware/supported/m68k.xml +++ /dev/null @@ -1,39 +0,0 @@ - - - - CPU, Main Boards, and Video Support - - -Complete information concerning supported M68000 based -(&architecture;) systems can be found at the -Linux/m68k FAQ. This section merely -outlines the basics. - - - -The &architecture; port of Linux runs on any 680x0 with a PMMU (Paged -Memory Management Unit) and a FPU (floating-point unit). This -includes the 68020 with an external 68851 PMMU, the 68030, and better, -and excludes the EC line of 680x0 processors. See the -Linux/m68k FAQ for complete details. - - - -There are four major supported -&architecture; flavors: Amiga, Atari, Macintosh -and VME machines. Amiga and Atari were the first two systems to which -Linux was ported; in keeping, they are also the two most -well-supported Debian ports. The Macintosh line is supported -incompletely, both by Debian and by the Linux kernel; see -Linux m68k for Macintosh for project -status and supported hardware. The BVM and Motorola single board -VMEbus computers are the most recent addition to the list of machines -supported by Debian. Ports to other &architecture; architectures, -such as the Sun3 architecture and NeXT black box, are underway but not -yet supported by Debian. - - - - - - diff --git a/en/install-methods/create-floppy.xml b/en/install-methods/create-floppy.xml index fb384b4ab..8489678ac 100644 --- a/en/install-methods/create-floppy.xml +++ b/en/install-methods/create-floppy.xml @@ -13,11 +13,6 @@ installer on hardware that cannot boot from CD or by other means. Booting the installer from floppy disk reportedly fails on Mac USB floppy drives. - - -Booting the installer from floppy disk is not supported on Amigas or -68k Macs. - Disk images are files containing the complete contents of a floppy @@ -107,7 +102,6 @@ to install it. &floppy-i386.xml; -&floppy-m68k.xml; &floppy-powerpc.xml; diff --git a/en/install-methods/download/m68k.xml b/en/install-methods/download/m68k.xml deleted file mode 100644 index a89b62076..000000000 --- a/en/install-methods/download/m68k.xml +++ /dev/null @@ -1,23 +0,0 @@ - - - - - - Choosing a Kernel - - - -Some m68k subarchs have a choice of kernels to install. In general we -recommend trying the most recent version first. If your subarch or -machine needs to use a 2.2.x kernel, make sure you choose one of the -images that supports 2.2.x kernels (see the MANIFEST). - - - - -All of the m68k images for use with 2.2.x kernels, require the kernel -parameter &ramdisksize;. - - - diff --git a/en/install-methods/downloading-files.xml b/en/install-methods/downloading-files.xml index 662986267..7be75fd04 100644 --- a/en/install-methods/downloading-files.xml +++ b/en/install-methods/downloading-files.xml @@ -29,7 +29,6 @@ lists each image and its purpose. &download-alpha.xml; &download-arm.xml; &download-powerpc.xml; -&download-m68k.xml; diff --git a/en/install-methods/floppy/m68k.xml b/en/install-methods/floppy/m68k.xml deleted file mode 100644 index 776bfd0bc..000000000 --- a/en/install-methods/floppy/m68k.xml +++ /dev/null @@ -1,27 +0,0 @@ - - - - - Writing Disk Images on Atari Systems - - -You'll find the &rawwrite.ttp; program in the same directory as the -floppy disk images. Start the program by double clicking on the -program icon, and type in the name of the floppy image file you want -written to the floppy at the TOS program command line dialog box. - - - - - - Writing Disk Images on Macintosh Systems - - -Since the current release does not yet support booting from floppies to -start the installation, there would be no point in doing this on -Macintosh Systems. However, these files are needed for the installation -of the operating system and modules, later in the process. - - - - diff --git a/en/install-methods/install-tftp.xml b/en/install-methods/install-tftp.xml index efd69e631..eff4340da 100644 --- a/en/install-methods/install-tftp.xml +++ b/en/install-methods/install-tftp.xml @@ -28,9 +28,6 @@ way is to use the BOOTP protocol. informs a computer of its IP address and where on the network to obtain a boot image. -Yet another alternative exists on VMEbus -systems: the IP address can be manually configured in boot ROM. - The DHCP (Dynamic Host Configuration Protocol) is a more flexible, backwards-compatible extension of BOOTP. Some systems can only be configured via DHCP. @@ -274,24 +271,6 @@ by adding it to the end of the OpenPROM boot command, such as boot net my-sparc.image. This must still reside in the directory that the TFTP server looks in. - - - - - BVM/Motorola TFTP Booting - - -For BVM and Motorola VMEbus systems copy the files -&bvme6000-tftp-files; to /tftpboot/. - - - -Next, configure your boot ROMs or BOOTP server to initially load the -tftplilo.bvme or -tftplilo.mvme files from the TFTP server. Refer -to the tftplilo.txt file for your subarchitecture -for additional system-specific configuration information. - diff --git a/en/partitioning/device-names.xml b/en/partitioning/device-names.xml index 7034eb676..0780ac543 100644 --- a/en/partitioning/device-names.xml +++ b/en/partitioning/device-names.xml @@ -59,19 +59,6 @@ The master and slave disks of the secondary controller can be called respectively. Newer IDE controllers can actually have two channels, effectively acting like two controllers. - -The letters may differ from what shows in the mac program pdisk -(i.e. what shows up as /dev/hdc on pdisk may show -up as /dev/hda in Debian). - - - - - - -The first ACSI device is named /dev/ada, the -second is named /dev/adb. - @@ -126,13 +113,6 @@ partition, that is, the primary partition holding the logical partitions, is not usable by itself. This applies to SCSI disks as well as IDE disks. - - -VMEbus systems using the TEAC FC-1 SCSI floppy drive will see it as normal -SCSI disk. To make identification of the drive simpler the installation -software will create a symbolic link to the appropriate device and name -it /dev/sfd0. - Sun disk partitions allow for 8 separate partitions (or slices). The diff --git a/en/partitioning/schemes.xml b/en/partitioning/schemes.xml index e1297d1d9..6ff4253ef 100644 --- a/en/partitioning/schemes.xml +++ b/en/partitioning/schemes.xml @@ -49,11 +49,6 @@ most cases. Of course, there are exceptions to these rules. If you are trying to solve 10000 simultaneous equations on a machine with 256MB of memory, you may need a gigabyte (or more) of swap. - - -On the other hand, Atari Falcons and Macs feel pain when swapping, so -instead of making a large swap partition, get as much RAM as possible. - On 32-bit architectures (i386, m68k, 32-bit SPARC, and PowerPC), the diff --git a/en/post-install/shutdown.xml b/en/post-install/shutdown.xml index 500495721..1bcf78855 100644 --- a/en/post-install/shutdown.xml +++ b/en/post-install/shutdown.xml @@ -19,7 +19,7 @@ the system. Alternatively you can press the key combination Ctrl Alt Del - or Control + or Control Shift Power on Macintosh systems. A last option is to log in as root and type one of the commands poweroff, halt or diff --git a/en/preparing/backup.xml b/en/preparing/backup.xml index 4d7bde4ee..548646bb7 100644 --- a/en/preparing/backup.xml +++ b/en/preparing/backup.xml @@ -25,17 +25,6 @@ have to reinstall your operating system's boot loader, or in many cases the whole operating system itself and all files on the affected partitions. - - - - -With the exception of the BVM and Motorola VMEbus computers, the only -supported installation method for m68k systems is booting from a local -disk or floppy using an AmigaOS/TOS/MacOS-based bootstrap, for these -machines you will need the original operating system in order to boot -Linux. In order to boot Linux on the BVM and Motorola VMEbus machines -you will need the BVMBug or 16xBug boot ROMs. - diff --git a/en/preparing/bios-setup/m68k.xml b/en/preparing/bios-setup/m68k.xml deleted file mode 100644 index 4c7d4b178..000000000 --- a/en/preparing/bios-setup/m68k.xml +++ /dev/null @@ -1,23 +0,0 @@ - - - - - - Firmware Revisions and Existing OS Setup - - - -&arch-title; machines are generally self-configuring and do not require -firmware configuration. However, you should make sure that you have -the appropriate ROM and system patches. On the Macintosh, MacOS -version >= 7.1 is recommended because version 7.0.1 contains a bug in -the video drivers preventing the boot loader from deactivating the -video interrupts, resulting in a boot hang. On the BVM VMEbus systems -you should make sure you are using BVMBug revision G or higher boot ROMs. -The BVMBug boot ROMs do not come as standard on the BVM systems but are -available from BVM on request free of charge. - - - - - diff --git a/en/preparing/minimum-hardware-reqts.xml b/en/preparing/minimum-hardware-reqts.xml index db88ed3f9..71ea4ed63 100644 --- a/en/preparing/minimum-hardware-reqts.xml +++ b/en/preparing/minimum-hardware-reqts.xml @@ -20,11 +20,6 @@ risk being frustrated if they ignore these suggestions. A Pentium 4, 1GHz system is the minimum recommended for a desktop system. - - -A 68030 or better processor is recommended for m68k -installs. You may get by with a little less drive space than shown. - Any OldWorld or NewWorld PowerPC can serve well as a desktop system. diff --git a/en/preparing/needed-info.xml b/en/preparing/needed-info.xml index 7589751f8..8dfffbd71 100644 --- a/en/preparing/needed-info.xml +++ b/en/preparing/needed-info.xml @@ -52,19 +52,13 @@ Often contains useful information on configuring or using your hardware. - + Linux Hardware Compatibility HOWTO - - -Linux/m68k FAQ - - - Linux/Alpha FAQ @@ -214,13 +208,9 @@ networking and e-mail. How many you have. Their order on the system. - - + Whether IDE (also known as PATA), SATA or SCSI. - - Whether IDE or SCSI (most m68k computers are SCSI). - Available free space. Partitions. diff --git a/en/preparing/non-debian-partitioning.xml b/en/preparing/non-debian-partitioning.xml index ad82c4d17..3ebf133cc 100644 --- a/en/preparing/non-debian-partitioning.xml +++ b/en/preparing/non-debian-partitioning.xml @@ -32,10 +32,6 @@ If you already have an operating system on your system (VM, z/OS, OS/390, …) - -(Amiga OS, Atari TOS, Mac OS, …) - - and want to stick Linux on the same disk, you will need to repartition the disk. Debian requires its own hard disk partitions. It cannot be installed on Windows or MacOS partitions. It may be able to share some @@ -49,7 +45,6 @@ You can find information about your current partition setup by using a partitioning tool for your current operating system, such as fdisk or PartitionMagic, such as Drive Setup, HD Toolkit, or MacTools, such as HD SC Setup, HDToolBox, or SCSITool, such as the VM diskmap. Partitioning tools always provide a way to show existing partitions without making changes. @@ -191,7 +186,6 @@ Boot the Debian installer to continue installing Debian. &nondeb-part-alpha.xml; &nondeb-part-x86.xml; -&nondeb-part-m68k.xml; &nondeb-part-sparc.xml; &nondeb-part-powerpc.xml; diff --git a/en/preparing/nondeb-part/m68k.xml b/en/preparing/nondeb-part/m68k.xml deleted file mode 100644 index 37734ca55..000000000 --- a/en/preparing/nondeb-part/m68k.xml +++ /dev/null @@ -1,127 +0,0 @@ - - - - - Partitioning in AmigaOS - - -If you are running AmigaOS, you can use the HDToolBox -program to adjust your native partitions prior to installation. - - - - - Partitioning in Atari TOS - - -Atari partition IDs are three ASCII characters, use LNX for -data and SWP for swap partitions. If using the low memory -installation method, a small Minix partition is also needed (about 2 MB), -for which the partition ID is MNX. Failure to set the -appropriate partition IDs not only prevents the Debian installation process -from recognizing the partitions, but also results in TOS attempting to use -the Linux partitions, which confuses the hard disk driver and renders the -whole disk inaccessible. - - - -There are a multitude of third party partitioning tools available (the -Atari harddisk utility doesn't permit changing the -partition ID); this manual cannot give detailed descriptions for all -of them. The following description covers SCSITool (from -Hard+Soft GmBH). - - - - -Start SCSITool and select the disk you want to partition -(Disk menu, item select). - - - - -From the Partition menu, select either -New to add new partitions or change the -existing partition sizes, or Change to -change one specific partition. Unless you have already created -partitions with the right sizes and only want to change the partition -ID, New is probably the best choice. - - - - -For the New choice, select -existing in the dialog box -prompting the initial settings. The next window shows a list of -existing partitions which you can adjust using the scroll buttons, or -by clicking in the bar graphs. The first column in the partition list -is the partition type; just click on the text field to edit it. When -you are finished changing partition settings, save the changes by -leaving the window with the OK button. - - - - -For the Change option, select the partition -to change in the selection list, and select other -systems in the dialog box. The -next window lists detailed information about the location of this -partition, and lets you change the partition ID. Save changes by -leaving the window with the OK button. - - - - -Write down the Linux names for each of the partitions you created or -changed for use with Linux — see . - - - - -Quit SCSITool using the -Quit item from the File -menu. The computer will reboot to make sure the changed partition -table is used by TOS. If you changed any TOS/GEM partitions, they will -be invalidated and have to be reinitialized (we told you to back up -everything on the disk, didn't we?). - - - - - - -There is a partitioning tool for Linux/m68k called -atari-fdisk in the installation system, but for now we -recommend you partition your disk using a TOS partition editor or some -disk tool. If your partition editor doesn't have an option to edit the -partition type, you can do this crucial step at a later stage (from -the booted temporary install RAMdisk). SCSITool is only -one of the partition editors we know of which supports selection of -arbitrary partition types. There may be others; select the tool that -suits your needs. - - - - - Partitioning in MacOS - - -Partitioning tools for Macintosh tested include pdisk, -HD SC Setup 7.3.5 (Apple), HDT 1.8 (FWB), -SilverLining (LaCie), and DiskTool (Tim -Endres, GPL). Full versions are required for HDT and -SilverLining. The Apple tool requires a patch in order -to recognize third-party disks (a description on how to patch HD -SC Setup using ResEdit can be found at -). - - - -For IDE based Macs, you need to use Apple Drive Setup to create -empty space for the Linux partitions, and complete the partitioning under -Linux, or use the MacOS version of pdisk available for download from -Alsoft. - - - - diff --git a/en/preparing/pre-install-bios-setup.xml b/en/preparing/pre-install-bios-setup.xml index 2e80da6b1..3bf222467 100644 --- a/en/preparing/pre-install-bios-setup.xml +++ b/en/preparing/pre-install-bios-setup.xml @@ -16,28 +16,13 @@ hardware; it is most critically invoked during the bootstrap process &bios-setup-i386.xml; -&bios-setup-m68k.xml; &bios-setup-powerpc.xml; &bios-setup-sparc.xml; &bios-setup-s390.xml; - + Hardware Issues to Watch Out For - - -Atari TT RAM boards are notorious for RAM problems under Linux; if you -encounter any strange problems, try running at least the kernel in -ST-RAM. Amiga users may need to exclude RAM using a booter memfile. - - - -FIXME: more description of this needed. - - - - - USB BIOS support and keyboards diff --git a/en/using-d-i/modules/clock-setup-finish.xml b/en/using-d-i/modules/clock-setup-finish.xml index 2adcb04cf..e704e56d1 100644 --- a/en/using-d-i/modules/clock-setup-finish.xml +++ b/en/using-d-i/modules/clock-setup-finish.xml @@ -15,7 +15,7 @@ systems are installed. In expert mode you will always be able to choose whether or not the clock is set to UTC. -Macintosh hardware clocks are normally +Macintosh hardware clocks are normally set to local time. If you want to dual-boot, select local time instead of UTC. Systems that (also) run Dos or Windows are normally diff --git a/en/using-d-i/modules/nobootloader.xml b/en/using-d-i/modules/nobootloader.xml index df251b1a5..f0e60d2c9 100644 --- a/en/using-d-i/modules/nobootloader.xml +++ b/en/using-d-i/modules/nobootloader.xml @@ -9,9 +9,7 @@ This option can be used to complete the installation even when no boot loader is to be installed, either because the arch/subarch doesn't provide one, or because none is desired (e.g. you will use existing -boot loader). This option is especially useful for -Macintosh, Atari, and Amiga systems, where the original operating system -must be maintained on the box and used to boot GNU/Linux. +boot loader). -- cgit debian/1.2.3+git2.25.1-1-2-gaceb0