diff options
Diffstat (limited to 'nl/appendix/plip.xml')
-rw-r--r-- | nl/appendix/plip.xml | 187 |
1 files changed, 0 insertions, 187 deletions
diff --git a/nl/appendix/plip.xml b/nl/appendix/plip.xml deleted file mode 100644 index 830d75232..000000000 --- a/nl/appendix/plip.xml +++ /dev/null @@ -1,187 +0,0 @@ -<!-- retain these comments for translator revision tracking --> -<!-- original version: 39644 untranslated --> - - <sect1 id="plip" arch="x86"> - <title>Installing &debian-gnu; over Parallel Line IP (PLIP)</title> - -<para> - -This section explains how to install &debian-gnu; on a computer without an -Ethernet card, but with just a remote gateway computer attached via -a Null-Modem cable (also called Null-Printer cable). The gateway -computer should be connected to a network that has a &debian; mirror -on it (e.g. to the Internet). - -</para><para> - -In the example in this appendix we will set up a PLIP connection using -a gateway connected to the Internet over a dial-up connection (ppp0). -We will use IP addresses 192.168.0.1 and 192.168.0.2 for the PLIP -interfaces on the target system and the source system respectively -(these addresses should be unused within your network address space). - -</para><para> - -The PLIP connection set up during the installation will also be available -after the reboot into the installed system (see <xref linkend="boot-new"/>). - -</para><para> - -Before you start, you will need to check the BIOS configuration (IO base -address and IRQ) for the parallel ports of both the source and target -systems. The most common values are <literal>io=0x378</literal>, -<literal>irq=7</literal>. - -</para> - - <sect2> - <title>Requirements</title> - -<itemizedlist> -<listitem><para> - -A target computer, called <emphasis>target</emphasis>, where &debian; will be -installed. - -</para></listitem> -<listitem><para> - -System installation media; see <xref linkend="installation-media"/>. - -</para></listitem> -<listitem><para> - -Another computer connected to the Internet, called <emphasis>source</emphasis>, -that will function as the gateway. - -</para></listitem> -<listitem><para> - -A DB-25 Null-Modem cable. See the -<ulink url="&url-plip-install-howto;">PLIP-Install-HOWTO</ulink> for more -information on this cable and instructions how to make your own. - -</para></listitem> -</itemizedlist> - - </sect2> - - <sect2> - <title>Setting up source</title> -<para> - -The following shell script is a simple example of how to configure the -source computer as a gateway to the Internet using ppp0. - -<informalexample><screen> -#!/bin/sh - -# We remove running modules from kernel to avoid conflicts and to -# reconfigure them manually. -modprobe -r lp parport_pc -modprobe parport_pc io=<replaceable>0x378</replaceable> irq=<replaceable>7</replaceable> -modprobe plip - -# Configure the plip interface (plip0 for me, see dmesg | grep plip) -ifconfig <replaceable>plip0 192.168.0.2</replaceable> pointopoint <replaceable>192.168.0.1</replaceable> netmask 255.255.255.255 up - -# Configure gateway -modprobe iptable_nat -iptables -t nat -A POSTROUTING -o <replaceable>ppp0</replaceable> -j MASQUERADE -echo 1 > /proc/sys/net/ipv4/ip_forward -</screen></informalexample> - -</para> - </sect2> - - <sect2> - <title>Installing target</title> -<para> - -Boot the installation media. The installation needs to be run in -expert mode; enter <userinput>expert</userinput> at the boot prompt. -If you need to set parameters for kernel modules, you also need to -do this at the boot prompt. For example, to boot the installer and -set values for the <quote>io</quote> and <quote>irq</quote> options -for the parport_pc module, enter the following at the boot prompt: - -<informalexample><screen> -expert parport_pc.io=<replaceable>0x378</replaceable> parport_pc.irq=<replaceable>7</replaceable> -</screen></informalexample> - -Below are the answers that should be given during various stages of -the installation. - -</para> - -<orderedlist> -<listitem><para> - -<guimenuitem>Load installer components from CD</guimenuitem> - -</para><para> - -Select the <userinput>plip-modules</userinput> option from the list; this -will make the PLIP drivers available to the installation system. - -</para></listitem> -<listitem><para> - -<guimenuitem>Detect network hardware</guimenuitem> - -</para> - - <itemizedlist> - <listitem><para> - -If target <emphasis>does</emphasis> have a network card, a list of driver -modules for detected cards will be shown. If you want to force &d-i; to -use plip instead, you have to deselect all listed driver modules. -Obviously, if target doesn't have a network card, the installer will not -show this list. - - </para></listitem> - <listitem><para> - -Because no network card was detected/selected earlier, the installer will -ask you to select a network driver module from a list. -Select the <userinput>plip</userinput> module. - - </para></listitem> - </itemizedlist> - -</listitem> -<listitem><para> - -<guimenuitem>Configure the network</guimenuitem> - - <itemizedlist> - <listitem><para> - -Auto-configure network with DHCP: No - - </para></listitem> - <listitem><para> - -IP address: <userinput><replaceable>192.168.0.1</replaceable></userinput> - - </para></listitem> - <listitem><para> - -Point-to-point address: -<userinput><replaceable>192.168.0.2</replaceable></userinput> - - </para></listitem> - <listitem><para> - -Name server addresses: you can enter the same addresses used on -source (see <filename>/etc/resolv.conf</filename>) - - </para></listitem> - </itemizedlist> - -</para></listitem> -</orderedlist> - - </sect2> - </sect1> |