diff options
Diffstat (limited to 'ja/preparing/nondeb-part/x86.xml')
-rw-r--r-- | ja/preparing/nondeb-part/x86.xml | 231 |
1 files changed, 0 insertions, 231 deletions
diff --git a/ja/preparing/nondeb-part/x86.xml b/ja/preparing/nondeb-part/x86.xml deleted file mode 100644 index bc29e45fd..000000000 --- a/ja/preparing/nondeb-part/x86.xml +++ /dev/null @@ -1,231 +0,0 @@ -<?xml version="1.0" encoding="EUC-JP"?> -<!-- retain these comments for translator revision tracking --> -<!-- original version: 43576 --> - - - <sect2 arch="x86"><title>DOS や Windows からのパーティション分割</title> -<para> - -<!-- -If you are manipulating existing FAT or NTFS partitions, it is -recommended that you either use the scheme below or native Windows or -DOS tools. Otherwise, it is not really necessary to partition from DOS -or Windows; the Linux partitioning tools will generally do a better -job. ---> -既存の FAT もしくは NTFS パーティションを扱う場合には、 -以降で説明する方法を用いるか、 -あるいは Windows や DOS のツールを用いることをお勧めします。 -扱わない場合には、 -DOS や Windows からパーティションを分割する必要はまったくありません。 -一般的に Linux 上のパーティション分割ツールを使えば、 -より適切に作業が行えます。 - -</para><para> - -<!-- -But if you have a large IDE disk, and are not using LBA addressing, -overlay drivers (sometimes provided by hard disk manufacturers), or a -new (post 1998) BIOS that supports large disk access extensions, then -you must locate your Debian boot partition carefully. In this case, -you will have to put the boot partition into the first 1024 cylinders -of your hard disk (usually around 524 megabytes, without BIOS -translation). This may require that you move an existing FAT or NTFS -partition. ---> -ただし大きな IDE ディスクを用いる場合で、 -LBA アドレスも、オーバーレイドライバ -(HDD のメーカーから提供されることが時々あります) も、 -ラージディスクアクセス拡張をサポートした新しい (1998 年以降の) BIOS も -ないときには、Debian のブートパーティションは注意して配置しなければなりません。 -このような場合、ブートパーティションをハードディスクの -先頭 1024 シリンダ以内に収めなければなりません -(これは BIOS 変換がなければ、通常 524 メガバイトになります)。 -これはすなわち、既存の FAT パーティションや NTFS -パーティションを移動しないといけないことを意味します。 - -</para> - - <sect3 id="lossless"> - <title>DOS, Windows, OS/2 から無駄なくパーティションを切り直す - </title> - -<para> - -<!-- -One of the most common installations is onto a system that already -contains DOS (including Windows 3.1), Win32 (such as Windows 95, 98, Me, -NT, 2000, XP), or OS/2, and it is desired to put Debian onto the same disk -without destroying the previous system. Note that the installer supports -resizing of FAT and NTFS filesystems as used by DOS and Windows. Simply -start the installer and when you get to the partitioning step, select the -option for <menuchoice> <guimenuitem>Manual</guimenuitem> </menuchoice> -partitioning, select the partition to resize, and specify its new size. -So in most cases you should not need to use the method described below. ---> -よくあるインストールのかたちとして、 -すでに DOS (Windows3.1 も含む), -Win32 (Windows 95, 98, Me, NT, 2000, XP), -OS/2 などが入っているシステムに新たに Debian をインストールする場合、 -既存のシステムを壊すことなく、 -同じディスクに Debian を入れるという需要があります。 -DOS や Windows で使用する、 -FAT ファイルシステム・NTFS ファイルシステムのリサイズを -インストーラはサポートしていることに注意してください。 -単にインストーラを起動し、パーティション分割の段階に来たら、 -<menuchoice> <guimenuitem>手動</guimenuitem> </menuchoice> -パーティション分割を選択し、リサイズするパーティションを選択、 -その後、新しいサイズを指定してください。 -ほとんどの場合、以下の方法を使う必要はありません。 - -</para><para> - -<!-- -Before going any further, you should have decided how you will be -dividing up the disk. The method in this section will only split a -partition into two pieces. One will contain the original OS and the -other will be used for Debian. During the installation of Debian, you -will be given the opportunity to use the Debian portion of the disk as you -see fit, i.e., as swap or as a file system. ---> -先に進む前に、ディスクをどのように分割するのか決めておかなければなりません。 -この節では 1 つのパーティションを 2 つに分割する方法のみ説明します。 -そのうち 1 つには既存の OS を残し、もう 1 つを Debian で利用します。 -なお、Debian に割り当てたディスク領域を、 -どの用途 (スワップかファイルシステムか) に -どのくらいずつ割り当てるかは、Debian インストールの途中で決定できます。 - -</para><para> - -<!-- -The idea is to move all the data on the partition to the beginning, -before changing the partition information, so that nothing will be -lost. It is important that you do as little as possible between the -data movement and repartitioning to minimize the chance of a file -being written near the end of the partition as this will decrease the -amount of space you can take from the partition. ---> -ここで紹介する方法は、パーティション情報を変更する前に、 -パーティション上の全データを、 -そのパーティションの先頭部分に移動するというものです。 -こうすることでデータの損失はなくなります。 -パーティションの後ろの方にファイルが存在すると、 -そのパーティションから得られる空き領域が減ってしまいます。 -従って、データの移動とパーティションの切り直しの最中に、 -ファイルがパーティションの終りの方に -書き込まれないようにするのが大切です。 - -</para><para> - -<!-- -The first thing needed is a copy of <command>fips</command> which is -available in the <filename>tools/</filename> directory on your nearest Debian -mirror. Unzip the archive and copy the files -<filename>RESTORRB.EXE</filename>, <filename>FIPS.EXE</filename> and -<filename>ERRORS.TXT</filename> to a bootable floppy. A bootable floppy can -be created using the command <filename>sys a:</filename> under DOS. -<command>fips</command> comes with very good documentation which you may -want to read. You will definitely need to read the documentation if -you use a disk compression driver or a disk manager. Create the disk -and read the documentation <emphasis>before</emphasis> you defragment the disk. ---> -まず最初に必要となるのは、<command>fips</command> のコピーです。 -これはお近くの Debian ミラーサイトの -<filename>tools/</filename> ディレクトリから入手できます。 -そのアーカイブを unzip して、<filename>RESTORRB.EXE</filename>, -<filename>FIPS.EXE</filename>, <filename>ERRORS.TXT</filename> の各ファイルを -起動可能なフロッピーにコピーしてください。 -起動可能なフロッピーは、DOS 上で <filename>sys a:</filename> というコマンドを -用いれば作成できます。 -<command>fips</command> には大変優れたドキュメントが用意されていますので、 -読んでおくとよいでしょう。 -特にディスク圧縮ドライバやディスクマネージャを使っている場合は、 -このドキュメントは必ず読んでおくべきでしょう。 -ディスクをデフラグメントする <emphasis>前</emphasis> に、 -このフロッピーディスクを作り、ドキュメントを読んでください。 - -</para><para> - -<!-- -The next thing needed is to move all the data to the beginning of the -partition. <command>defrag</command>, which comes standard with DOS 6.0 and -later, can easily do the job. See the <command>fips</command> documentation -for a list of other software that may do the trick. Note that if you -have Windows 9x, you must run <command>defrag</command> from there, since -DOS doesn't understand VFAT, which is used to support for long -filenames, used in Windows 95 and higher. ---> -次に必要となるのは、すべてのデータをパーティションの前方に移動する作業です。 -DOS 6.0 以降に標準で用意されている <command>defrag</command> を使えば、 -これは簡単です。同じような作業を行える他のソフトウェアの一覧は、 -<command>fips</command> のドキュメントに書いてあります。 -Windows9x を使っている場合は、Windows9x の方から <command>defrag</command> -を実行しなければならないことに注意してください。 -DOS は VFAT (Windows95 以降で使われており、 -長いファイル名をサポートする) を認識できないからです。 - -</para><para> - -<!-- -After running the defragmenter (which can take a while on a large -disk), reboot with the <command>fips</command> disk you created in the -floppy drive. Simply type <filename>a:\fips</filename> and follow the directions. ---> -デフラグツールを実行した後 (大きなディスクでは少々時間がかかります)、 -先ほど作成した、<command>fips</command> を収めたフロッピーディスクを -ドライブに挿入してリブートしてください。 -起動したらそのまま <filename>a:\fips</filename> と打ち込んで、 -その指示にしたがってください。 - -</para><para> - -<!-- -Note that there are many other partition managers out there, in -case <command>fips</command> doesn't do the trick for you. ---> -<command>fips</command> ではうまくいかない場合のために、 -他にもパーティション管理ソフトウェアはたくさんあることを -心に留めておいてください。 - -</para> - </sect3> - - <sect3 id="partitioning-for-dos"><title>DOS のパーティションを分割する</title> - -<para> - -<!-- -If you are partitioning for DOS drives, or changing the size of DOS -partitions, using Linux tools, many people experience problems working -with the resulting FAT partitions. For instance, some have reported -slow performance, consistent problems with <command>scandisk</command>, or -other weird errors in DOS or Windows. ---> -DOS のドライブにパーティションを作成したり、DOS パーティションの容量を -変更したりする作業を Linux のツールで行うと、 -その結果できた FAT パーティションでの作業に問題が残ることがあるようです。 -例えば DOS や Windows 上でパフォーマンスが落ちたり、 -<command>scandisk</command> で整合性の問題が起きたり、 -その他原因不明のエラーに遭遇したりといった報告例があります。 - -</para><para> - -<!-- -Apparently, whenever you create or resize a partition for DOS use, -it's a good idea to fill the first few sectors with zeros. You should do -this prior to running DOS's <command>format</command> command by executing -the following command from Linux: ---> -どうやら、 -DOS で使用するパーティションを作成したりその容量を変更したりする場合は、 -その最初のいくつかのセクタを 0 で埋めておくのが良いようです。 -DOS の <command>format</command> コマンドを実行する前に、 -Linux から次のコマンドを実行してください。 - -<informalexample><screen> -# dd if=/dev/zero of=/dev/hdXX bs=512 count=4 -</screen></informalexample> - -</para> - </sect3> - </sect2> |