diff options
Diffstat (limited to 'ja/boot-installer/mips.xml')
-rw-r--r-- | ja/boot-installer/mips.xml | 160 |
1 files changed, 0 insertions, 160 deletions
diff --git a/ja/boot-installer/mips.xml b/ja/boot-installer/mips.xml deleted file mode 100644 index 9341a44e5..000000000 --- a/ja/boot-installer/mips.xml +++ /dev/null @@ -1,160 +0,0 @@ -<?xml version="1.0" encoding="EUC-JP"?> -<!-- retain these comments for translator revision tracking --> -<!-- original version: 35613 --> - - - <sect2 arch="mips" id="boot-tftp"><title>TFTP での起動</title> - - <sect3> -<!-- - <title>SGI TFTP Booting</title> ---> - <title>SGI の TFTP での起動</title> -<para> - -<!-- -After entering the command monitor use ---> -SGI のマシンで、コマンドモニタに入ったところで - -<informalexample><screen> -bootp(): -</screen></informalexample> - -<!-- -on SGI machines to boot linux and to begin installation of the Debian -Software. In order to make this -work you may have to unset the <envar>netaddr</envar> environment -variable. Type ---> -と入力すると、linux が起動して Debian ソフトウェアのインストールが始まります。 -インストーラを正しく動作させるには、 -環境変数 <envar>netaddr</envar> の設定を解除しなければならないこともあります。 -これにはコマンドモニタから - -<informalexample><screen> -unsetenv netaddr -</screen></informalexample> - -<!-- -in the command monitor to do this. ---> -とします。 - -</para> - </sect3> - - <sect3> -<!-- - <title>Broadcom BCM91250A and BCM91480B TFTP Booting</title> ---> - <title>Broadcom BCM91250A/BCM91480B の TFTP での起動</title> -<para> - -<!-- -On the Broadcom BCM91250A and BCM91480B evaluation boards, you have to load the SiByl boot -loader via TFTP which will then load and start the Debian installer. In -most cases, you will first obtain an IP address via DHCP but it is also -possible to configure a static address. In order to use DHCP, you can -enter the following command on the CFE prompt: ---> -Broadcom BCM91250A/BCM91480B 評価ボードでは、 -Debian インストーラをロードし起動するのに、 -SiByl ブートローダを TFTP 経由でロードしなければなりません。 -ほとんどの場合、始めに IP アドレスを DHCP 経由で取得しますが、 -静的アドレスを設定することも可能です。 -DHCP を使用するためには、CFE プロンプトで以下のコマンドを入力します。 - -<informalexample><screen> -ifconfig eth0 -auto -</screen></informalexample> - -<!-- -Once you have obtained an IP address, you can load SiByl with the following -command: ---> -いったん IP アドレスを取得したら、以下のコマンドで SiByl をロードできます。 - -<informalexample><screen> -boot 192.168.1.1:/boot/sibyl -</screen></informalexample> - -<!-- -You need to substitute the IP address listed in this example with either -the name or the IP address of your TFTP server. Once you issue this -command, the installer will be loaded automatically. ---> -この例の IP アドレスを、使用する TFTP サーバの名前や IP アドレスで -置き換える必要があります。 -いったんこのコマンドを発行すると、インストーラは自動でロードされます。 - -</para> -</sect3> - </sect2> - - <sect2 arch="mips"><title>ブートパラメータ</title> - - <sect3> -<!-- - <title>SGI TFTP Booting</title> ---> - <title>SGI の TFTP での起動</title> -<para> - -<!-- -On SGI machines you can append boot parameters to the -<command>bootp():</command> command in the command monitor. ---> -SGI のマシンでは、コマンドモニタの -<command>bootp():</command> コマンドにブートパラメータを追加します。 - -</para><para> - -<!-- -Following the <command>bootp():</command> command you can give the -path and name of the file to boot if you did not give an explicit name -via your bootp/dhcp server. Example: ---> -bootp/dhcp サーバの方から名前を与えていない場合は、 -<command>bootp():</command> の後に -起動させるファイルのパスと名前を与えることが可能です。 -例: - -<informalexample><screen> -bootp():/boot/tftpboot.img -</screen></informalexample> - -<!-- -Further kernel parameters can be passed via <command>append</command>: ---> -さらにカーネルパラメータは <command>append</command> を通して渡せます: - -<informalexample><screen> -bootp(): append="root=/dev/sda1" -</screen></informalexample> - -</para> - </sect3> - - <sect3> -<!-- - <title>Broadcom BCM91250A and BCM91480B TFTP Booting</title> ---> - <title>Broadcom BCM91250A/BCM91480B の TFTP での起動</title> -<para> - -<!-- -You cannot pass any boot parameters directly from the CFE prompt. Instead, -you have to edit the <filename>/boot/sibyl.conf</filename> file on the TFTP -server and add your parameters to the <replaceable>extra_args</replaceable> -variable. ---> -CFE プロンプトからは、どんなブートパラメータも直接渡せません。 -その代わり、 -TFTP サーバの <filename>/boot/sibyl.conf</filename> ファイルを編集し、 -パラメータを <replaceable>extra_args</replaceable> に追加する必要があります。 - -</para> - </sect3> - - </sect2> |