diff options
Diffstat (limited to 'it/install-methods/tftp')
| -rw-r--r-- | it/install-methods/tftp/rarp.xml | 90 |
1 files changed, 19 insertions, 71 deletions
diff --git a/it/install-methods/tftp/rarp.xml b/it/install-methods/tftp/rarp.xml index 4d779d05f..53c931dd3 100644 --- a/it/install-methods/tftp/rarp.xml +++ b/it/install-methods/tftp/rarp.xml @@ -1,5 +1,5 @@ <!-- retain these comments for translator revision tracking --> -<!-- original version: 28997 --> +<!-- original version: 39897 --> <sect2 condition="supports-rarp" id="tftp-rarp"> @@ -8,7 +8,7 @@ <para> <!-- -To setup RARP, you need to know the Ethernet address (a.k.a. the MAC address) +To set up RARP, you need to know the Ethernet address (a.k.a. the MAC address) of the client computers to be installed. If you don't know this information, you can @@ -30,79 +30,27 @@ ripristino) e usare il comando <userinput>/sbin/ifconfig eth0</userinput>. </para><para> <!-- -On a RARP server system using a Linux 2.2.x kernel, -you need to populate the kernel's RARP table. -To do this, run the following commands: ---> - -Su un sistema con Linux 2.2.x e un server RARP è necessario popolare la -tabella RARP del kernel. Per farlo usare i seguenti comandi: - -<informalexample><screen> -# <userinput>/sbin/rarp -s -<replaceable>client-hostname</replaceable> -<replaceable>client-enet-addr</replaceable></userinput> - -# <userinput>/usr/sbin/arp -s -<replaceable>client-ip</replaceable> -<replaceable>client-enet-addr</replaceable></userinput> -</screen></informalexample> - -<!-- -If you get ---> - -Se si ottiene - -<informalexample><screen> -SIOCSRARP: Invalid argument -</screen></informalexample> - -<!-- -you probably need to load the RARP kernel module or else recompile the -kernel to support RARP. Try <userinput>modprobe rarp</userinput> and -then try the <command>rarp</command> command again. ---> - -probabilmente si deve caricare il modulo del kernel RARP oppure -ricompilare il kernel inserendo il supporto RARP. Eseguire -<userinput>modprobe rarp</userinput> e poi provare di nuovo a usare il -comando <command>rarp</command>. - -</para><para> - -<!-- -On a RARP server system using a Linux 2.4.x kernel, -there is no RARP module, and -you should instead use the <command>rarpd</command> program. The -procedure is similar to that used under SunOS in the following -paragraph. ---> - -Su un sistema con Linux 2.4.x e un server RARP non esiste il modulo RARP e -al suo posto si deve usare il programma <command>rarpd</command>. La -procedura è simile a quella da usare in SunOS ed è spiegata nel prossimo -paragrafo. - -</para><para> - -<!-- -Under SunOS, you need to ensure that the Ethernet hardware address for -the client is listed in the <quote>ethers</quote> database (either in the +On a RARP server system using a Linux 2.4 or 2.6 kernel, or Solaris/SunOS, +you use the <command>rarpd</command> program. +You need to ensure that the Ethernet hardware address for the client is +listed in the <quote>ethers</quote> database (either in the <filename>/etc/ethers</filename> file, or via NIS/NIS+) and in the <quote>hosts</quote> database. Then you need to start the RARP daemon. -In SunOS 4, issue the command (as root): -<userinput>/usr/etc/rarpd -a</userinput>; in SunOS 5, use -<userinput>/usr/sbin/rarpd -a</userinput>. +Issue the command (as root): <userinput>/usr/sbin/rarpd -a</userinput> +on most Linux systems and SunOS 5 (Solaris 2), +<userinput>/usr/sbin/in.rarpd -a</userinput> on some other Linux systems, +or <userinput>/usr/etc/rarpd -a</userinput> in SunOS 4 (Solaris 1). --> -Sotto SunOS ci si deve assicurare che l'indirizzo Ethernet del -client sia elencato nel database <quote>ethers</quote> (nel file -<filename>/etc/ethers</filename> o tramite NIS/NIS+) e sia elencato -anche nel database <quote>hosts</quote>. Poi si deve avviare il demone -RARP, in SunOS 4 eseguire (da root): <userinput>/usr/etc/rarpd --a</userinput>; in SunOS 5 usare <userinput>/usr/sbin/rarpd --a</userinput>. +Su un server RARP con kernel Linux 2.4 o 2.6, oppure con Solaris/SunOS, +usare il programma <command>rarpd</command>. Assicurarsi che l'indirizzo +Ethernet del client sia elencato nel database <quote>ethers</quote> (nel +file <filename>/etc/ethers</filename> o tramite NIS/NIS+) e nel database +<quote>hosts</quote>. Poi si deve avviare il demone RARP eseguendo (da +root): <userinput>/usr/sbin/rarpd -a</userinput> per la maggior parte dei +sistemi Linux e SunOS 5 (Solaris 2), <userinput>/usr/sbin/in.rarpd +-a</userinput> per alcuni sistemi Linux oppure <userinput>/usr/etc/rarpd +-a</userinput> per SunOS 4 (Solaris 1). </para> </sect2> |