diff options
Diffstat (limited to 'eu/boot-installer/trouble.xml')
-rw-r--r-- | eu/boot-installer/trouble.xml | 200 |
1 files changed, 0 insertions, 200 deletions
diff --git a/eu/boot-installer/trouble.xml b/eu/boot-installer/trouble.xml deleted file mode 100644 index b393ca3d9..000000000 --- a/eu/boot-installer/trouble.xml +++ /dev/null @@ -1,200 +0,0 @@ -<!-- retain these comments for translator revision tracking --> -<!-- original version: 15221 untranslated --> - - <sect1 id="boot-troubleshooting"> - <title>Troubleshooting the Install Process</title> -<para> -</para> - - <sect2 id="unreliable-floppies"> - <title>Floppy Disk Reliability</title> - -<para> - -The biggest problem for people installing Debian for the first time -seems to be floppy disk reliability. - -</para><para> - -The boot floppy is the floppy with the worst problems, because it -is read by the hardware directly, before Linux boots. Often, the -hardware doesn't read as reliably as the Linux floppy disk driver, and -may just stop without printing an error message if it reads incorrect -data. There can also be failures in the Driver Floppies most of which -indicate themselves with a flood of messages about disk I/O errors. - -</para><para> - -If you are having the installation stall at a particular floppy, the -first thing you should do is re-download the floppy disk image and -write it to a <emphasis>different</emphasis> floppy. Simply -reformatting the old -floppy may not be sufficient, even if it appears that the floppy was -reformatted and written with no errors. It is sometimes useful to try -writing the floppy on a different system. - -</para><para> - -One user reports he had to write the images to floppy -<emphasis>three</emphasis> times before one worked, and then -everything was fine with the third floppy. - -</para><para> - -Other users have reported that simply rebooting a few times with the -same floppy in the floppy drive can lead to a successful boot. This is -all due to buggy hardware or firmware floppy drivers. - -</para> - </sect2> - - <sect2><title>Boot Configuration</title> - -<para> - -If you have problems and the kernel hangs during the boot process, -doesn't recognize peripherals you actually have, or drives are not -recognized properly, the first thing to check is the boot parameters, -as discussed in <xref linkend="boot-parms"/>. - -</para><para> - -If you are booting with your own kernel instead of the one supplied -with the installer, be sure that <userinput>CONFIG_DEVFS</userinput> is set in -your kernel. The installer requires -<userinput>CONFIG_DEVFS</userinput>. - -</para><para> - -Often, problems can be solved by removing add-ons and peripherals, and -then trying booting again. <phrase arch="x86">Internal modems, sound -cards, and Plug-n-Play devices can be especially problematic.</phrase> - -</para><para> - -There are, however, some limitations in our boot floppy set with -respect to supported hardware. Some Linux-supported platforms might -not be directly supported by our boot floppies. If this is the case, -you may have to create a custom boot disk (see -<xref linkend="rescue-replace-kernel"/>), or investigate network -installations. - -</para><para> - -If you have a large amount of memory installed in your machine, more -than 512M, and the installer hangs when booting the kernel, you may -need to include a boot argument to limit the amount of memory the -kernel sees, such as <userinput>mem=512m</userinput>. - -</para> - </sect2> - - <sect2 id="kernel-msgs"> - <title>Interpreting the Kernel Startup Messages</title> - -<para> - -During the boot sequence, you may see many messages in the form -<computeroutput>can't find <replaceable>something</replaceable> -</computeroutput>, or <computeroutput> -<replaceable>something</replaceable> not present</computeroutput>, -<computeroutput>can't initialize <replaceable>something</replaceable> -</computeroutput>, or even <computeroutput>this driver release depends -on <replaceable>something</replaceable> </computeroutput>. -Most of these messages are harmless. You -see them because the kernel for the installation system is built to -run on computers with many different peripheral devices. Obviously, no -one computer will have every possible peripheral device, so the -operating system may emit a few complaints while it looks for -peripherals you don't own. You may also see the system pause for a -while. This happens when it is waiting for a device to respond, and -that device is not present on your system. If you find the time it -takes to boot the system unacceptably long, you can create a -custom kernel later (see <xref linkend="kernel-baking"/>). - -</para> - </sect2> - - - <sect2 id="problem-report"> - <title>Bug Reporter</title> -<para> - -If you get through the initial boot phase but cannot complete the -install, the bug reporter menu choice may be helpful. It copies system -error logs and configuration information to a user-supplied floppy. -This information may provide clues as to what went wrong and how to -fix it. If you are submitting a bug report you may want to attach -this information to the bug report. - -</para><para> - -Other pertinent installation messages may be found in -<filename>/target/var/log/debian-installer/</filename> during the -installation, and <filename>/var/log/debian-installer/</filename> -after the computer has been booted into the installed system. - -</para> - </sect2> - - <sect2 id="submit-bug"> - <title>Submitting Bug Reports</title> -<para> - -If you still have problems, please submit a bug report. Send an email -to <email>submit@bugs.debian.org</email>. You -<emphasis>must</emphasis> include the following as the first lines of -the email: - -<informalexample><screen> - -Package: installation-reports -Version: <replaceable>version</replaceable> - -</screen></informalexample> - -Be sure to fill in <replaceable>version</replaceable> with the -version of the debian-installer that you used. The version number can -be found if you press <keycap>F1</keycap> key on the -<prompt>boot:</prompt> prompt of your installation media. You should -also mention where did you download the installation media, or the -source of a CD you bought. - -</para><para> - -You should also include the following information in your bug report. -If you use the program <command>reportbug</command> to submit your -report, this information will be included automatically. - -<informalexample><screen> - -<phrase arch="x86"> -flavor: <replaceable>flavor of image you are using</replaceable> -</phrase> -architecture: &architecture; -model: <replaceable>your general hardware vendor and model</replaceable> -memory: <replaceable>amount of RAM</replaceable> -scsi: <replaceable>SCSI host adapter, if any</replaceable> -cd-rom: <replaceable>CD-ROM model and interface type, e.g., ATAPI</replaceable> -network card: <replaceable>network interface card, if any</replaceable> -pcmcia: <replaceable>details of any PCMCIA devices</replaceable> - -</screen></informalexample> - -</para><para> - -Depending on the nature of the bug, it also might be useful to report -whether you are installing to IDE or SCSI disks, other peripheral -devices such as audio, disk capacity, and the model of video card. - -</para><para> - -In the bug report, describe what the problem is, including the last -visible kernel messages in the event of a kernel hang. Describe the -steps that you did which brought the system into the problem state. - -</para> - - </sect2> - - </sect1> |