diff options
Diffstat (limited to 'eu/boot-installer/arm.xml')
-rw-r--r-- | eu/boot-installer/arm.xml | 109 |
1 files changed, 0 insertions, 109 deletions
diff --git a/eu/boot-installer/arm.xml b/eu/boot-installer/arm.xml deleted file mode 100644 index fadc600e3..000000000 --- a/eu/boot-installer/arm.xml +++ /dev/null @@ -1,109 +0,0 @@ -<!-- retain these comments for translator revision tracking --> -<!-- original version: 11648 untranslated --> - - <sect2 arch="arm" id="boot-tftp"><title>Booting from TFTP</title> - -&boot-installer-intro-net.xml; - - <sect3 arch="arm"><title>Booting from TFTP on NetWinder</title> - -<para> - -NetWinders have two network interfaces: The 10Mbps NE2000-compatible -card is <filename>eth0</filename> and the 100Mbps Tulip card is -<filename>eth1</filename>. - -</para><note><para> - -You need NeTTrom 2.2.1 or later to boot the -installation system. NeTTrom 2.3.3 is recommended: get these files -from -<ulink url="ftp://ftp.netwinder.org/pub/netwinder/firmware/"></ulink>: -<itemizedlist> -<listitem><para> - -<filename>nettrom-2.3-3.armv4l.rpm</filename> - -</para></listitem> -<listitem><para> - -<filename>nettrom-2.3.3.bin</filename> - -</para></listitem> -<listitem><para> - -<filename>nettrom-2.3.3.bin.md5sum</filename> - -</para></listitem> -</itemizedlist> - -</para></note><para> - -After rebooting and interrupting the boot process during the countdown, you -must first configure the network either with a static address: -<informalexample><screen> - - NeTTrom command-> setenv eth0_ip 192.168.0.10/24 - -</screen></informalexample> -where 24 is the number of set bits in the netmask, or a dynamic address: -<informalexample><screen> - - NeTTrom command-> boot diskless - -</screen></informalexample> - -</para><para> - -You may also need to configure the <userinput>route1</userinput> -settings if the TFTP -server is not on the local subnet. The rest of the config is pretty -standard (the save-all step is optional): -<informalexample><screen> - - NeTTrom command-> setenv kerntftpserver 192.168.0.1 - NeTTrom command-> setenv kerntftpfile tftpboot.img - NeTTrom command-> save-all - NeTTrom command-> setenv netconfig_eth0 flash - NeTTrom command-> setenv kernconfig tftp - -</screen></informalexample> - -</para><para> - -Only the last two of these interfere with normal disk booting, so it is -safe to <command>save-all</command> right before it, which will -store the network settings in case you need to boot from the network -again. Use the <command>printenv</command> command to review your -environment settings. Finally, if your <envar>cmdappend</envar> -NeTTrom variable has the <option>noinitrd</option> option (which is -necessary to boot 2.4 kernels), you must remove it so the downloaded -kernel can boot with its attached ramdisk. - -</para> - </sect3> - - <sect3 arch="arm"><title>Booting from TFTP on CATS</title> - -<para> - -On CATS machines, use <command>boot de0:</command> or similar at the -Cyclone prompt. - -</para> - </sect3> - </sect2> - - - - <sect2 arch="arm"><title>Booting from CD-ROM</title> - -&boot-installer-intro-cd.xml; - -<para> - -To boot a CD-ROM from the Cyclone console prompt, use the command -<command>boot cd0:cats.bin</command> - -</para> - </sect2> |