1 files changed, 0 insertions, 109 deletions
diff --git a/da/boot-installer/arm.xml b/da/boot-installer/arm.xml
deleted file mode 100644
index fadc600e3..000000000
--- a/da/boot-installer/arm.xml
+++ /dev/null
@@ -1,109 +0,0 @@
-<!-- retain these comments for translator revision tracking -->
-<!-- original version: 11648 untranslated -->
-
-  <sect2 arch="arm" id="boot-tftp"><title>Booting from TFTP</title>
-
-&boot-installer-intro-net.xml;
-
-  <sect3 arch="arm"><title>Booting from TFTP on NetWinder</title>
-
-<para>
-
-NetWinders have two network interfaces: The 10Mbps NE2000-compatible
-card is <filename>eth0</filename> and the 100Mbps Tulip card is
-<filename>eth1</filename>.
-
-</para><note><para>
-
-You need NeTTrom 2.2.1 or later to boot the
-installation system. NeTTrom 2.3.3 is recommended: get these files
-from 
-<ulink url="ftp://ftp.netwinder.org/pub/netwinder/firmware/"></ulink>:
-<itemizedlist>
-<listitem><para>
-
-<filename>nettrom-2.3-3.armv4l.rpm</filename>
-
-</para></listitem>
-<listitem><para>
-
-<filename>nettrom-2.3.3.bin</filename>
-
-</para></listitem>
-<listitem><para>
-
-<filename>nettrom-2.3.3.bin.md5sum</filename>
-
-</para></listitem>
-</itemizedlist>
-
-</para></note><para>
-
-After rebooting and interrupting the boot process during the countdown, you 
-must first configure the network either with a static address:
-<informalexample><screen>
-
-    NeTTrom command-> setenv eth0_ip 192.168.0.10/24
-
-</screen></informalexample>
-where 24 is the number of set bits in the netmask, or a dynamic address:
-<informalexample><screen>
-
-    NeTTrom command-> boot diskless
-
-</screen></informalexample>
-
-</para><para>
-
-You may also need to configure the <userinput>route1</userinput>
-settings if the TFTP
-server is not on the local subnet.  The rest of the config is pretty 
-standard (the save-all step is optional):
-<informalexample><screen>
-
-    NeTTrom command-> setenv kerntftpserver 192.168.0.1
-    NeTTrom command-> setenv kerntftpfile tftpboot.img
-    NeTTrom command-> save-all
-    NeTTrom command-> setenv netconfig_eth0 flash
-    NeTTrom command-> setenv kernconfig tftp
-
-</screen></informalexample>
-
-</para><para>
-
-Only the last two of these interfere with normal disk booting, so it is 
-safe to <command>save-all</command> right before it, which will
-store the network settings in case you need to boot from the network
-again. Use the <command>printenv</command> command to review your
-environment settings. Finally, if your <envar>cmdappend</envar>
-NeTTrom variable has the <option>noinitrd</option> option (which is  
-necessary to boot 2.4 kernels), you must remove it so the downloaded 
-kernel can boot with its attached ramdisk.
-
-</para>
-  </sect3>
-
-  <sect3 arch="arm"><title>Booting from TFTP on CATS</title>
-
-<para>
-
-On CATS machines, use <command>boot de0:</command> or similar at the
-Cyclone prompt.
-
-</para>
-   </sect3>
-  </sect2>
-
-
-
-  <sect2 arch="arm"><title>Booting from CD-ROM</title>
-
-&boot-installer-intro-cd.xml;
-
-<para>
-
-To boot a CD-ROM from the Cyclone console prompt, use the command
-<command>boot cd0:cats.bin</command>
-
-</para>
-  </sect2>