Update list of supported ARM devices.

1 files changed, 0 insertions, 94 deletions

diff --git a/en/boot-installer/arm.xml b/en/boot-installer/arm.xml
index 9adc0447c..57e4485c8 100644
--- a/en/boot-installer/arm.xml
+++ b/en/boot-installer/arm.xml
@@ -19,100 +19,6 @@
 
 &boot-installer-intro-firmware.xml;
 
-   <sect3 arch="arm" id="boot-firmware-nslu2"><title>Booting the NSLU2</title>
-<para>
-
-There are three ways how to put the installer firmware into flash:
-
-</para>
-
-    <sect4 arch="arm"><title>Using the NSLU2 web interface</title>
-<para>
-
-Go to the administration section and choose the menu item
-<literal>Upgrade</literal>.  You can then browse your disk for the
-installer image you have previously downloaded.  Then press the
-<literal>Start Upgrade</literal> button, confirm, wait for a few minutes
-and confirm again.  The system will then boot straight into the installer.
-
-</para>
-    </sect4>
-
-    <sect4 arch="arm"><title>Via the network using Linux/Unix</title>
-<para>
-
-You can use <command>upslug2</command> from any Linux or Unix machine to
-upgrade the machine via the network.  This software is packaged for
-&debian;.
-
-First, you have to put your NSLU2 in upgrade mode:
-
-<orderedlist>
-<listitem><para>
-
-Disconnect any disks and/or devices from the USB ports.
-
-</para></listitem>
-<listitem><para>
-
-Power off the NSLU2
-
-</para></listitem>
-<listitem><para>
-
-Press and hold the reset button (accessible through the small hole on the
-back just above the power input).
-
-</para></listitem>
-<listitem><para>
-
-Press and release the power button to power on the NSLU2.
-
-</para></listitem>
-<listitem><para>
-
-Wait for 10 seconds watching the ready/status LED. After 10 seconds it
-will change from amber to red. Immediately release the reset button.
-
-</para></listitem>
-<listitem><para>
-
-The NSLU2 ready/status LED will flash alternately red/green (there is a 1
-second delay before the first green). The NSLU2 is now in upgrade mode.
-
-</para></listitem>
-</orderedlist>
-
-See the <ulink
-url="http://www.nslu2-linux.org/wiki/OpenSlug/UsingTheBinary">NSLU2-Linux
-pages</ulink> if you have problems with this.
-
-Once your NSLU2 is in upgrade mode, you can flash the new image:
-
-<informalexample><screen>
-sudo upslug2 -i di-nslu2.bin
-</screen></informalexample>
-
-Note that the tool also shows the MAC address of your NSLU2, which may come
-in handy to configure your DHCP server.  After the whole image has been
-written and verified, the system will automatically reboot.  Make sure you
-connect your USB disk again now, otherwise the installer won't be able to
-find it.
-
-</para>
-    </sect4>
-
-    <sect4 arch="arm"><title>Via the network using Windows</title>
-<para>
-
-There is <ulink
-url="http://www.everbesthk.com/8-download/sercomm/firmware/all_router_utility.zip">a
-tool</ulink> for Windows to upgrade the firmware via the network.
-
-</para>
-    </sect4>
-   </sect3>
-
    <sect3 arch="arm" id="boot-firmware-ss4000e">
    <title>Booting the SS4000-E</title>
 <para>